Filter
Top Products
Operation Guide 4330
2
• Proper signal reception can be difficult or even impossible under the conditions listed
below.
• Signal reception is normally better at night than during the day.
• Time calibration signal reception takes from four to seven minutes, but in some
cases it can take as long as 14 minutes. Take care that you do not perform any
button operations or move the watch during this time.
Inside or
among
buildings
Inside a
vehicle
Near a
construction
site, airport, or
other sources
of electrical
noise
Near high-
tension
power lines
Among or
behind
mountains
Near
household
appliances,
office
equipment,
or a mobile
phone
• The time calibration signal the watch will attempt to pick up depends on its current
Home City code setting as shown below.
Home City Code
NYC (GMT –5), CHI (GMT –6)
DEN (GMT –7), LAX (GMT –8)
ANC (GMT –9), HNL (GMT –10)
TYO (GMT +9)
Frequency
60.0 kHz
40.0 kHz
60.0 kHz
Transmitter
Fort Collins, Colorado
(the United States)
Fukushima (Japan)
Fukuoka/Saga (Japan)
Reception Ranges
Fort Collins
2,000 miles
(3,000 kilometers)
600 miles
(1,000 kilometers)
1,000
kilometers
1,000
kilometers
Fukuoka/Saga
500
kilometers
Fukushima
500
kilometers
• At distances further than about 600 miles (1,000 kilometers) from the Fort Collins
(the United States) transmitter, signal reception may not be possible during certain
times of year or times of day. Radio interferance may also cause problems with
reception.
• At distances further than about 500 kilometers (310 miles) from the Fukushima and
Fukuoka/ Saga (Japan) transmitter, signal reception may not be possible during
certain times of year or times of day. Radio interferance may also cause problems
with reception.
• Even when the watch is within the reception range of the transmitter, signal
reception will be impossible if the signal is blocked by mountains or other geological
formations between the watch and signal source.
• Signal reception is affected by weather, atmospheric conditions, and seasonal
changes.
• See the information under “Signal Reception Troubleshooting” if you experience
problems with time calibration signal reception.
About Auto Receive
The watch receives the time calibration signal automatically up to six times a day.
When any auto receive is successful, the remaining auto receive operations are not
performed. The reception schedule (calibration times) depends on your currently
selected Home City, and whether standard time or Daylight Saving Time is selected
for your Home City.
Your City Code
Auto Receive Start Times
123456
TYO (GMT +9)
Standard Time
Midnight 1:00 am 2:00 am 3:00 am 4:00 am 5:00 am
Standard Time and
Midnight 1:00 am 2:00 am 3:00 am 4:00 am 5:00 am
Daylight Saving Time
NYC (GMT –5),
CHI (GMT –6)
DEN (GMT –7),
LAX (GMT –8)
ANC (GMT –9),
HNL (GMT –10)
Note
• Auto receive is supported in all modes except while a stopwatch elapsed time
operation is in progress.
• Auto receipt of the calibration signal is designed to be performed early in the
morning, while you sleep (provided that the Timekeeping Mode time is set correctly).
Before going to bed for the night, remove the watch from your wrist, and put it in a
location where it can receive the signal easily.
• The watch receives the calibration signal for two to 14 minutes everyday when the
time in the Timekeeping Mode reaches each of the calibration times. Do not perform
any button operation within ten minutes before or after any one of the calibration
times. Doing so can interfere with correct calibration.
• Remember that reception of the calibration signal depends on the current time in the
Timekeeping Mode.
To perform manual receive
1.Place the watch on a stable surface so its 12 o’clock
side is facing towards a window.
2.In the Timekeeping Mode, hold down A for about two
seconds until the watch beeps.
3.The stopwatch second hand will move to READY to
indicate that the watch is setting up for time calibration
reception.
• The stopwatch second hand will move to WORK and
stay there while actual reception is in progress.
• The hour and minute hands continue to keep time
normally.
• Time calibration signal reception takes from four to
seven minutes, but in some cases it can take up to 14
minutes. Take care that you do not perform any button
operations or move the watch during this time.
• If reception is successful, the second hand will move to
Y (YES). 10 seconds later, the hands will move to the
correct time.
WORK
READY
Y (YES)
N (NO)
Note
• To interrupt a receive operation and return to the Timekeeping Mode, press any
button.
• If reception is not successful, the stopwatch second hand will move to N (NO).
5 second later, the stopwatch second hand will resume normal operation, without
any adjustment of the hand setting.
• If the stopwatch second hand is pointing to Y (YES) or N (NO), you can return to the
Timekeeping Mode by pressing any button.
Viewing the Latest Signal Reception Results
You can use the Receive Result Mode to check if signal reception was performed
correctly.
To check the latest signal reception results
1.In the Timekeeping Mode, press A.
• If the watch was able to perform a successful signal
receive operation since midnight, the stopwatch second
hand will move to Y (YES). If the watch has been unable
to receive any signal successfully, the second hand will
move to N (NO).
• The watch will return to the Timekeeping Mode after five
seconds or when you press A.
• The current receive result is cleared when the first auto
receive operation is performed on the following day. This
means Y (YES) indicates successful signal reception
since the start of the current day.
• Y (YES) continues to be indicated even if an attempt at
manual receive fails after auto receive is successful.
• If you adjust the time or date setting manually, the
second hand will move to N (NO).
Signal Reception Troubleshooting
Check the following points whenever you experience problems with signal reception.
• For further information, see “Important!” under “Time Calibration Signal Reception”
and “Radio-controlled Atomic Timekeeping Precautions”.
• You changed the time setting
manually.
•
The watch was not in the
Timekeeping Mode, or you performed
some button operation during the
auto receive operation.
• Signal reception results are reset at
midnight each day.
• The Home City setting is not correct
for the area where you are using
the watch.
The
stopwatch
second hand
is pointing at
N (NO).
Time setting is
incorrect
following signal
reception.
• Perform manual signal
receive or wait until the next
auto signal receive operation
is performed.
• Check to make sure the
watch is in a location where it
can receive the signal.
• Select the correct Home City.
What you should doProblem Probable Cause
World Time
The World Time Mode shows you the current time in 27
cities (29 time zones) around the world.
• If the current time shown for a city is wrong, check your
Home City settings and make the necessary changes.
• All of the operations in this section are performed in the
World Time Mode.
To view the time in another city
While in the World time Mode, use D to select a city
code.
The World Time dial hands will move to indicate the
current time in the selected city code.
• The watch will beep if the city you select is your current
Home City.
• For full information on city codes, see "City Code Table".
World Time dial
To check whether the World Time is Standard Time or Daylight Saving Time
While in the World Time Mode, press A.
Standard Time is indicated if the second hand moves to 6 o’clock,
while Daylight Saving Time is indicated if it moves to 12 o’clock.
• The second hand will return to normal timekeeping after
about two or three seconds.
To toggle a city code time between Standard Time and
Daylight Saving Time
In the World Time Mode, hold down A for about five seconds.
• The above operation toggles the city code to Daylight
Saving Time. This is indicated by the second hand
moving to 12 o
’
clock for two or three seconds. After that
it will return to normal timekeeping.
• The above operation toggles the city code to Standard Time. This indicated by the
second hand moving to 6 o’clock for two or three seconds. After that it will return to
normal timekeeping.
• Note that you cannot swith between Standard Time and Daylight Saving Time while
GMT is selected as the city code.
Second hand