Casio 4322 Watch User Manual


  Open as PDF
of 6
 
Operation Guide 4321 4322
4
Do this:
Use D (east) and B (west).
Press D.
Press D.
Press D.
Use D (+) and B (–).
Use D (+) and B (–).
Use D (+) and B (–).
Screen: To do this:
Change the city code
Toggle between Daylight Saving
Time (
ON) , Standard Time (OF),
or Auto DST (A)
Toggle between 12-hour (
) and
24-hour ( ) timekeeping
Reset the seconds to
Change the hour or minutes
Change the year
Change the month or day
• See “City Code Table” for a complete list of available city codes.
• For details about configuring settings for the Power Saving feature, see “Power
Saving Function”.
4. Press A to exit the setting screen.
• The second hand will advance at high speed to the correct position in accordance
with the digital time seconds count, and resume normal movement from there.
• When you exit the setting screen, the analog hands are adjusted automatically to
match the digital time. See “Analog Timekeeping” for more information.
Note
• Auto DST (
A) can be selected only while BER, PAR, LON, or ATH is selected as the
Home City code. For more information, see “Daylight Saving Time (DST)” below.
Daylight Saving Time (DST)
Daylight Saving Time (summer time) advances the time setting by one hour from
Standard Time. Remember that not all countries or even local areas use Daylight
Saving Time.
The time calibration signals transmitted from Anthorn and Mainflingen includes both
Standard Time and DST data. When the Auto DST setting is turned on, the watch
switches between Standard Time and DST (summer time) automatically in
accordance with the received time signal.
• Auto DST (
A) can be selected only while BER, PAR, LON, or ATH is selected as the
Home City code.
• The default DST setting is Auto DST (
A) whenever you select BER, PAR, LON,
or
ATH as your Home City code.
• If you experience problems receiving the time calibration signal in your area, it is
probably best to switch between Standard Time and Daylight Saving Time (summer
time) manually.
Auto DST (
A
) DST off (
OF
) DST on (
ON
)
4. When the setting you want is selected, press A to exit the setting screen.
• The DST indicator appears on the display to indicate that Daylight Saving Time is
turned on.
Analog Timekeeping
The analog time of this watch is synchronized with the digital time. The analog time
setting is adjusted automatically whenever you change the digital time.
Note
• The hands for the analog timepiece move to adjust to a new setting whenever any of
the following occurs.
When you change the digital time setting manually
When the digital time setting is changed by time calibration signal reception
When you change the Home City code and/or DST setting
• If the analog time does not match the digital time for any reason, use the procedure
described under “To adjust the analog time” to match the analog setting to the digital
setting.
• Whenever you need to adjust both the digital and the analog time settings manually,
make sure you adjust the digital setting first.
• Depending on how much the hands have to move in order to adjust to the digital
time, it may take some time before they stop moving.
To adjust the analog time
1.In the Timekeeping Mode, press C five times to enter
the Hand Setting Mode.
2.Hold down A until
starts to flash, which
indicates the setting screen.
• The second hand will move at high speed to the 12
o’clock position, where it will stop.
3.If the second hand is not pointing precisely at 12 o’clock
at this time, use D to adjust its position.
• Each press of D causes the second hand to advance
by one second.
4. Press C. This will cause the time on the digital display to flash, which indicates that
adjustment of hour and minute hands is selected.
5. Use D and B to adjust the analog setting as described below.
When you want to do this:
Move the hand setting
forward 10 seconds
Move the hand setting back
10 seconds
Move the hand setting a short
way forward at high speed
Move the hand setting a
short way back at high speed
Move the hand setting a long
way forward at high speed
Move the hand setting a long
way back at high speed
Perform this button operation:
• Press D.
• Press B.
• Hold down D.
• Release D when the hands reach the setting
you want.
• Hold down B.
• Release B when the hands reach the setting
you want.
• While holding down D to move the hands at
high-speed, press B to lock the high-speed
hand movement.
• To stop the hand movement, press any
button.
• Hand movement stops automatically if the hour
hand makes one full (12-hour) revolution.
• While holding down B to move the hands at
high-speed, press D to lock the high-speed
hand movement.
• To stop the hand movement, press any
button.
• Hand movement stops automatically if the hour
hand makes one full (12-hour) revolution.
Power Supply
This watch is equipped with a solar cell and a special rechargeable battery
(secondary battery) that is charged by the electrical power produced by the solar cell.
The illustration shown below shows how you should position the watch for charging.
Example: Orient the watch so its face
is pointing at a light source.
• The illustration shows how to position
a watch with a resin band.
• Note that charging efficiency drops
when any part of the solar cell is
blocked by clothing, etc.
• You should try to keep the watch
outside of your sleeve as much as
possible. Charging is reduced
significantly if the face is only partially
covered.
Solar cell
Timekeeping
Use the Timekeeping Mode to set and view the current time and date. This section
also explains how to manually set the current date and time.
• In the Timekeeping Mode, press D to display the last signal screen. The last signal
screen shows the date and time of the last successful time calibration signal
reception.
• In the Timekeeping Mode, press A to cycle through the digital time screens as
shown below.
• All of the operations in this section are performed in the Timekeeping Mode, which
you can enter by pressing C.
Last Signal Screen
Reception date
Day of week
Press A.
Day
▲
▲
▲
Receiving indicator
▲
A
2 seconds
2 seconds
2 seconds
A
Press D.
Reception Time
Date Screen
Receiving
Indicator and
Seconds Count
▲
Seconds
Hour :
Minutes
PM indicator
Current Time
Screen
Setting the Digital Time and Date Manually
Make sure you select your Home City code before you change the current time and
date settings. World Time Mode times are all displayed in accordance with the
Timekeeping Mode settings. Because of this, World Time Mode times will not be
correct if you do not select the proper Home City code before setting the time and
date in the Timekeeping Mode.
To set the current digital time and date manually
1.In the Timekeeping Mode, hold down A until the city
code starts to flash, which indicates the setting screen.
• The second hand will move at high speed to the 12
o’clock position, where it will stop.
2.Use C to move the flashing in the sequence shown
below to select other settings.
3. When the setting you want to change is flashing, use B and/or D to change it as
described below.
Seconds
Hour
12/24-Hour
Format
Year
DST
DayPower Saving
City Code
Month
Minutes
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
City code
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
To change the Daylight Saving Time (summer time) setting
1. In the Timekeeping Mode, hold down A until the city code starts to flash, which
indicates the setting screen.
2. Press C to display the DST setting screen.
3. Use D to cycle through the DST settings in the sequence shown below.
6. Press A to exit the setting screen.
• The minute hand will be adjusted slightly to match the seconds when you exit the
setting screen.
• To return to the Timekeeping Mode, press C.
 previous next