Filter
Top Products
1
Operation Guide ANA (3H3EDB)
MA0909-EA
Using the Stopwatch
The stopwatch lets you measure elapsed time up to 11 hours, 59 minutes, 59 seconds.
You can also correct the position of the stopwatch second hand when necessary.
• The illustration shows a time of 2 hours, 20 minutes, 40 seconds.
• Do not try to perform stopwatch operations while the crown is pulled out either to
the first or second click. If you try to press a button, you might accidentally cause
the crown to rotate and change the current time or day setting.
To measure elapsed time
1. Press A to start the stopwatch.
2. Press A to stop the stopwatch.
• You can resume the measurement operation by pressing A again.
3. Press B to reset the stopwatch.
Adjusting the Stopwatch Second Position
Use of the stopwatch can cause the starting positions of the stopwatch minute hand
and second hand to become misaligned. Use the following procedures to check hand
alignment and to adjust the positions of the hands so they point to 12 o’clock when
the stopwatch is reset.
To adjust the positions of the stopwatch hands
1. Press B to reset the stopwatch, and check the alignment of the stopwatch minute
hand and second hand.
2. Pull out the crown to the second click.
3. Press A to move the stopwatch second hand forward until it points to 12 o’clock.
4. If the stopwatch minute hand is aligned correctly, proceed to step 5. If the
stopwatch hour hand and stopwatch minute hand are also misaligned, press B so
the stopwatch minute hand jumps to 0.
5. After making the adjustments you want, push the crown back in to its normal position.
• Note that pulling the crown out also stops the timekeeping second hand. After
performing the above procedure, you should also adjust the timekeeping setting.
To set the time
1. Pull out the crown to the second click.
• This causes the second hand to stop.
2. Set the hands by rotating the crown.
Move the minute hand four or five
minutes past the time you want to
set, and then back it up to the proper
setting.
3.
Push the crown back in to the normal
position to restart timekeeping.
To set the day
1. Pull out the crown to the first click.
2. Set the day by rotating the crown.
3. Push the crown back in to the normal
position.
• Avoid setting the day between 9:00
p.m. and 1:00 a.m. (the day display
may not change in the following day).
■ For a watch with an elapsed time bezel
Rotate the elapsed time bezel to align the
mark with the
minute hand.
After certain amount of time elapsed, read the graduation on
the elapsed time bezel which the minute hand points to.
The elapsed time is indicated.
• Some water resistant models are equipped with a screw lock
crown.
• With such models, you must unscrew the crown in the
direction noted in the illustration to loosen it before you can
pull it out. Do not pull too forcibly on such crowns.
• Also note that such watches are not water resistant while
their crowns are loosened. Be sure to screw the crowns
back in as far as they will go after making any setting.
Specifications
Accuracy at normal temperature: ± 20 seconds a month
Display: 3 analog hands (timekeeping hour and minutes, stopwatch seconds),
3 dials (timekeeping seconds, stopwatch hours and minutes), day
Stopwatch function:Measuring capacity: 11:59'59''/Measuring unit: 1 second
Measuring modes: Elapsed time
Battery: One silver oxide battery (Type: SR927W)
Approximately 2 years on type SR927W (assuming one stopwatch operation 60 min./day)
50
40
30
20
10
Elapsed time bezel
• Be sure to keep all user documentation handy for future reference.
• Your watch may differ somewhat from the one shown in the illustration.
Stopwatch hours
Hour
Stopwatch minutes
Minutes
Crown
(normal position)
Day
Seconds
Stopwatch seconds
First click
(setting day)
Second click
(setting time)