Filter
Top Products
Operation Guide 3267 3400
E-20
Stopwatch Button
Operation
From all-zeros,
press D to start.
Press A to
display lap/split
time.
Press D to stop
elapsed time
measurrement and
then press A to reset.
Data Storage Description
Creates a new log. Stores the date the button was pressed,
and the new log number.
Creates a new record with each button operation. Stores the
lap and split times and total elapsed time at each point the
button is pressed.
Resets the elapsed time to all zeros without recording data.
How stopwatch data is stored
The following table shows how stopwatch data is stored when you perform stopwatch
button operations.
• See “Recall Mode” (page E-21) for details on how to recall time records from
memory.
E-21
Recall Mode
Use the Recall Mode to recall and delete logs and records
you stored in the Stopwatch Mode. You can use the Recall
Mode to view both lap and split time records.
• When you enter the Recall Mode, the newest log
recorded in the Stopwatch Mode will appear first. If there
are no logs in memory,
xxxxxxxx
xxxxxxxx
xxxx appears on the display.
• You can use the Recall Mode to check memory data
even while a stopwatch elapsed time measurement
operation is in progress. However, the time data that is
currently being measured will not appear in the Recall
Mode.
• You can convert a lap time saved in the Stopwatch
Mode to a split time (page E-22).
Day of week
Month – Day
Log number
Log Title Screen
E-22
To recall stopwatch time records
1. In the Stopwatch Mode, check to make sure that the displays reset to all zeros
(page E-15).
• If all zeros are not displayed, reset the stopwatch.
2. Use the A button to select either the lap time screen (to view lap time records) or
the split time screen (to view split time records) (page E-15 and E-17).
• To convert a lap time saved in the Stopwatch Mode to a split time, select the split
time screen.
3. Press the C button to enter the Recall Mode.
4. Use the A button to scroll through the log title screens from the newest to the
oldest until the title screen of the log whose records you want to view is displayed.
5. Press D to scroll through the records contained in the log you selected in step 4,
from the oldest to the newest.
E-23
• Whether you will be able to view lap time records or split time records will depend on
the screen you selected in step 2, above.
PressD.
▲
▲
Lap number
Split number
Log number
Log Title Screen
First record Last record
▲
▲
Lap time
Split time
▲
E-24
To delete a log
1. In the Recall Mode, display the title screen of the log you want to delete.
2. Hold down B and D until CLR stops flashing on the display.
• This deletes the log and all the records inside it.
• Deleting a single log slides all newer logs (ones with higher log numbers) upwards to
fill the empty space. This cause the log numbers of all the newer logs to be reduced
by 1. If there are six logs currently in memory (numbered 01 through 06) and you
delete log 03, the numbers of logs that previously were numbered 04, 05, and 06 will
change to 03, 04, and 05.
E-25
Countdown Timer
You can set the countdown timer within a range of one
minute to 24 hours. An alarm sounds when the countdown
reaches zero.
• You also can select auto-repeat, which automatically
restarts the countdown from the original value you set
whenever zero is reached.
• All of the operations in this section are performed in the
Countdown Timer Mode, which you enter by pressing
C (page E-7).
l
l
l
l
l
l
l
l
l
SecondsHours
Minutes
Timekeeping
Mode time
Auto-repeat
on indicator
E-26
To use the countdown timer
Press D while in the Countdown Timer Mode to start the countdown timer.
• When the end of the countdown is reached and auto-repeat is turned off, the alarm
sounds for 10 seconds or until you stop it by pressing any button. The countdown
time is reset automatically to its starting value after the alarm stops.
• When auto-repeat is turned on, the countdown will restart automatically without
pausing when it reaches zero. The alarm sounds when the countdown reaches zero.
• The countdown timer measurement operation continues even if you exit the
Countdown Timer Mode.
• Press D while a countdown operation is in progress to pause it. Press D again to
resume the countdown.
• To stop a countdown operation completely, first pause it (by pressing D), and then
press A. This returns the countdown time to its starting value.
E-27
To configure countdown start time and auto-repeat settings
1.While the countdown start time is on the display in the
Countdown Timer Mode, hold down A until the hour
setting of the countdown start time starts to flash, which
indicates the setting screen.
• If the countdown start time is not displayed, use the
procedure under “To use the countdown timer” (page
E-26) to display it.
2.Press C to move the flashing in the sequence shown
below, and select the setting you want to change.
Start Time
(Minutes)
Auto-Repeat
On/Off
Start Time
(Hours)
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
On/Off status
Auto-repeat on indicator
E-28
3. Perform the following operations, depending on which setting currently is selected
on the display.
• While the start time setting is flashing, use D (+) and B (–) to change it.
• Set 0:00 to specify 24 hours.
• While the auto-repeat on/off setting (0N or 0F) is flashing on the display, press
D to toggle auto-repeat on (0N) and off (0F).
4. Press A to exit the setting screen.
• The auto-repeat on indicator (
) is displayed on the Countdown Timer Mode
screen while this function is turned on.
• Frequent use of auto-repeat and the alarm can run down battery power.
E-29
Alarms
You can set up to three independent multi-function alarms
with hour, minutes, month, and day. When an alarm is
turned on, the alarm tone sounds when the alarm time is
reached. One of the alarms can be configured as a
snooze alarm or a one-time alarm, while the other two are
one-time alarms.
You also can turn on an Hourly Time Signal that causes
the watch to beep twice every hour on the hour.
• There are three alarm screens numbered 1 through 3.
The hourly time signal screen is indicated by :00.
• All of the operations in this section are performed in the
Alarm Mode, which you enter by pressing C (page E-7).
Alarm time
(Hour : Minutes)
Alarm number
Alarm date
(Month – Day)