Filter
Top Products
Operation Guide 3135 3206
7
2. While the Moon information (Moon age and
phase) and tide information (current tide level
and tide range) are displayed, hold down E
until the hour digits start to flash. This is the
high tide time hour adjustment screen.
3. Use A (+) and C (–) to change the hour
setting.
4. When the hour is the setting you want, press
D.
• This will cause the minute digits to flash.
5. Use A (+) and C (–) to change the minute
setting.
6. When the minute setting is the way you want,
press E to exit the adjustment screen and
return to the Tide/Moon Data Mode screen.
• Pressing A and C at the same time while the
time adjustment screen is displayed (steps 2
through 5 above) will return the high tide time
to its initial factory default setting.
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
Hour
Minute
• The high tide time setting is not affected by the DST (summer time) setting
of the Timekeeping Mode.
• On some days, there are two high tides. With this watch, you can adjust the
first high tide time only. The second high tide time for that day is adjusted
automatically based on the first high tide time.
Reversing the Displayed Moon Phase
The left-right (east-west) appearance of the Moon depends on whether the
Moon is north of you (northerly view) or south of you (southerly view) as you
view it.
You can use the procedure below to reverse the displayed Moon phase so it
matches the actual appearance of the Moon where you are located.
• To determine the viewing direction of the Moon, use a compass to take a
direction reading of the Moon at its meridian passage.
• For information about the Moon phase indicator, see “Moon Phase
Indicator”.
To reverse the displayed Moon phase
1. In the Tide/Moon Data Mode, hold down E
until the hour digits start to flash.
2. Press D twice.
• This will cause the Moon phase indicator to
flash. This is the indicator switching screen.
3. Press A to toggle the Moon phase indicator
between the southerly view (indicated by
) and northerly view (indicated by ).
• Northerly view: Moon is north of you.
• Southerly view: Moon is south of you.
4. When the Moon phase indicator setting is the
way you want, press E to exit the switching
screen and return to the Tide/Moon Data
Mode screen.
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
Countdown Timer
The countdown timer can be set within a range of
one minute to 60 minutes. An alarm sounds when
the timer reaches zero. The press of a button will
start the countdown timer from the currently set
start time, and a progress beeper sounds to keep
you informed of the current status of the
countdown. These features make it possible to
use the watch for yacht racing.
• All of the operations in this section are
performed in the Countdown Timer Mode,
which you enter by pressing D.
Configuring Countdown Timer Settings
The following are the settings you should configure before actually using the
countdown timer.
Countdown start time and reset time
Progress beeper (on/off)
Minutes
Seconds
Current
time
• See “To configure countdown timer settings” for information about setting up
the timer.
• For details about the progress beeper, see “Progress Beeper”.
Reset Time
You can set a “reset time”, which is a kind of alternate countdown start time
you can recall with the press of a button any time a countdown operation is in
progress.
Countdown End Beeper
The watch beeps each second of the final 10 seconds before a countdown
reaches zero, and at zero. The first five beeps (seconds 10 through 6) are
higher pitched than the final five beeps (seconds 5 through 1). The watch
emits a longer beep to signal when the countdown reaches zero.
Progress Beeper
The progress beeper actually includes two beepers: a reset time beeper and
a reset period beeper.
• Note that the reset time beeper and reset period beeper operate only while
the progress beeper is turned on. For more information, see “To turn the
progress beeper on and off”.
Reset Time Beeper
The reset time beeper is similar to the countdown end beeper. The watch
beeps each second of the final 10 seconds before the countdown reaches the
reset time.
Reset Period Beeper
The reset period is in the portion of the countdown between the reset time
and zero. While timing is the reset period, the watch will beep four times at the
top of each minute and 10 seconds before the end of the countdown.
Countdown Timer Examples
Countdown start time: 10 minutes; Reset time: 5 minutes
Progress beeper: On
10'00"
Start Time Reset Time
0'00"1'00" 0'10"2'00"3'00"4'00"5'00"
Reset Period
Reset Period Beeper
Countdown
End Beeper
Reset Time Beeper
0'01"0'02"0'03"0'04"0'05"0'06"0'07"0'08"0'09"0'10" 0'00"
To configure countdown timer settings
1. While the countdown start time is on the
display in the Countdown Timer Mode, hold
down E until the countdown start time setting
starts to flash, which indicates the setting
screen.
• If the countdown start time is not displayed,
use the procedure under “To use the
countdown timer” to display it.
2. Press D to move the flashing in the sequence
shown below to select other settings.
Start
Time
Reset
Time
3. When the setting you want to change is flashing, use A and C to change
it as described below.
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
Setting
Start Time
Reset Time
Screen Button Operations
Use A (+) and C (–) to change the setting.
•You can set a start time in the range of 1 to 60
minutes in 1-minute increments.
Use A (+) and C (–) to change the setting.
•You can set a reset time in the range of 1 to 5
minutes in 1-minute increments.
4. Press E to exit the setting screen.
• The reset time setting must be less than the countdown start time setting.
To turn the progress beeper on and off
Pressing B while the countdown start time is on the display or while a
countdown timer operation is in progress in the Countdown Timer Mode
toggles progress beeper operation on (
displayed) and off ( displayed).
To use the countdown timer
In the Countdown Timer Mode, press A to start
the countdown timer.
• The countdown timer measurement operation
continues even if you exit the Countdown Timer
Mode.
• The table below describes button operations
you can perform to control countdown
operations.
To do this:
Stop the countdown operation
Resume a stopped countdown operation
Display the countdown start time
Stop the countdown operation and display the reset
time
Start the countdown from the displayed reset time
Do this:
Press A.
Press A again.
While the countdown is
stopped, press C.
Press C.
Press A.
l
l
l
l
l
l
l
l
l
l
l
l
Countdown Timer Beeper Operations
The watch beeps at various times during a countdown so you can keep
informed about the countdown status without looking at the display. The
following describes the types of beeper operations the watch performs during
a countdown.