Filter
Top Products
Operation Guide 2895
2
Countdown start time: 10 minutes; Reset time: 5 minutes; Timer mode: Elapsed time;
Progress beeper: Off
10'00"
0'00"5'00"
Countdown
End Beeper
Elapsed time
measurement
Start Time Reset Time
To configure the countdown timer
1.While the countdown start time is on the display in the
Countdown Timer Mode, hold down A until the
countdown start time setting starts to flash, which
indicates the setting screen.
• If the countdown start time is not displayed, use the
procedure under “To use the countdown timer” to
display it.
2.Press C to move the flashing in the sequence shown
below to select other settings.
Start
Time
Reset
Time
Timer
Mode
Progress
Beeper
3. When the setting you want to change is flashing, use D and B to change it as
described below.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Setting
Start Time
Reset Time
Timer Mode
Progress
Beeper
Screen Button Operations
Use D (+) and B (–) to change the setting.
• You can set a start time in the range of 1 to 60 minutes
in 1-minute increments.
Use D (+) and B (–) to change the setting.
• You can set a reset time in the range of 1 to 5 minutes
in 1-minute increments.
Press D to toggle between the auto-repeat mode (ON)
and the elapsed time mode (OFF).
• An auto-repeat indicator (
) appears when the auto-
repeat mode is selected.
Press D to toggle progress beeper on (ON) and off (OFF).
• A progress beeper indicator (
) appears when this
setting is turned on.
4. Press A to exit the setting screen.
• The reset time setting must be less than the countdown start time setting.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
To use the countdown timer
In the Countdown Timer Mode, press D to start the
countdown timer.
• The countdown timer measurement operation continues
even if you exit the Countdown Timer Mode.
• The table below describes button operations you can
perform to control countdown operations.
To do this:
Stop the countdown operation
Resume a stopped countdown operation
Display the countdown start time
Stop the countdown operation and display the reset time
Start the countdown from the displayed reset time
Do this:
Press D.
Press D again.
While the countdown is
stopped, press B.
Press B.
Press D.
• The table below describes button operations you can perform during an elapsed
time measurement operation in the elapsed time mode.
To do this:
Stop the elapsed time operation
Resume a stopped elapsed time operation
Display the countdown start time
Stop the elapsed time operation and display the reset time
Start the countdown from the displayed reset time
Do this:
Press D.
Press D again.
While the elapsed time is
stopped, press B.
Press B.
Press D.
Alarms
You can set five independent Daily Alarms. When an
alarm is turned on, the alarm tone sounds when the
alarm time is reached. One of the alarms can be
configured as a snooze alarm or a one-time alarm,
while the other four are one-time alarms.
You can also turn on an Hourly Time Signal that causes
the watch to beep twice every hour on the hour, and a
brightness alarm that beeps whenever the watch is
moved from an area where it is dark to an area where it
is light.
• There are five alarm screens numbered 1 through 5. The hourly time signal screen
is indicated by :00. The brightness alarm screen shows ON or OFF.
• When you enter the Alarm Mode, the screen you were viewing when you last exited
the mode appears first.
• All of the operations in this section are performed in the Alarm Mode, which you
enter by pressing C.
Alarm number
Alarm time
(Hour : Minutes)
Timekeeping
Mode time
Mode
indicator
To set an alarm time
1.In the Alarm Mode, use D to scroll through the alarm
screens until the one whose time you want to set is
displayed.
x3 x4x1 x2
:00 x5
ON or OFF
• You can configure Alarm 1 as a snooze alarm or a one-time alarm. Alarms 2
through 5 can be used as one-time alarms only.
• The snooze alarm repeats every five minutes.
2. After you select an alarm, hold down A until the hour setting of the alarm time
starts to flash. This indicates the setting screen.
3. Press C to move the flashing between the hour and minute settings.
4. While a setting is flashing, use D (+) and B (–) to change it.
Countdown Timer Examples
Countdown start time: 10 minutes; Reset time: 5 minutes; Timer mode: Auto-repeat;
Progress beeper: On
10'00"
Start Time Reset Time
0'00"1'00" 0'30"2'00"3'00"4'00"5'00"
Reset Period
Reset Period Progress Beeper
Countdown
End Beeper
Reset Time Beeper
• When setting the alarm time using the 12-hour format, take care to set the time
correctly as a.m. (no indicator) or p.m. (P indicator).
5. Press A to exit the setting screen.
Alarm Operation
The alarm sounds at the preset time for about 10 seconds. In the case of the snooze
alarm, the alarm operation is performed a total of seven times, every five minutes, or
until you turn the alarm off or change it to a one-time alarm.
The watch also has a brightness alarm. When turned on, the brightness alarm causes
the watch to beep for 10 seconds when the watch is brought from the dark into the
light. The following are the conditions for brightness alarm operation.
• The watch needs to be in the dark for about 30 to 35 minutes for the brightness
alarm to become activated.
• The brightness alarm sounds for about 10 seconds, about 15 to 20 minutes after the
watch is next exposed to light.
• The brightness alarm sounds only once and then turns off automatically.
Note
• Pressing any button stops the alarm tone operation.
• Performing any one of the following operations during a 5-minute interval between
snooze alarms cancels the current snooze alarm operation.
Displaying the Timekeeping Mode setting screen
Displaying the Alarm
1
setting screen
To test the alarm
In the Alarm Mode, hold down D to sound the alarm.
To turn Alarms
22
22
2
through
55
55
5
on and off
1.In the Alarm Mode, use D to select a one-time alarm
(alarm number 2 through 5).
2.Press B to toggle the displayed alarm on and off.
• Turning on a one-time alarm (2 through 5) displays the
one-time alarm on indicator (
) on its screen.
• The one-time alarm on indicator is displayed in all
modes.
• If any alarm is on, the one-time alarm on indicator is
shown on the display in all modes.
One-time alarm on
indicator
To select the operation of Alarm
11
11
1
1. In the Alarm Mode, use D to select Alarm 1.
2. Press B to cycle through the available settings in the sequence shown below.
Snooze alarm on indicator ( ) and one-time alarm on indicator ( )
One-time alarm on Snooze alarm on Alarm off
• The applicable alarm on indicator ( or ) is displayed in all modes when an
alarm is turned on.
• The snooze alarm on indicator flashes during the 5-minute intervals between
alarms.
• Displaying the Alarm 1 setting screen while the snooze alarm is turned on
automatically turns off the snooze alarm (making Alarm 1 a one-time alarm).
To turn the hourly time signal and the brightness alarm on and off
1.In the Alarm Mode, use D to select the Hourly Time
Signal or the brightness alarm.
2.Press B to toggle the displayed item on and off.
• Turning on the Hourly Time Signal displays the hourly
time signal on indicator (
) on its screen.
• Turning on the brightness alarm displays the brightness
alarm on indicator (
B
R
I
G
H
T
) on its screen.
• The hourly time signal on indicator and brightness alarm
on indicator are displayed in all modes.
Hourly time signal on
indicator
Brightness alarm on
indicator