Filter
Top Products
Operation Guide 2858 2859 2860 2861
3
To delete all Time Recorder times
1.Enter the Time Recorder Mode.
2.Hold down A for about two seconds to delete all Time Recorder times.
• The recorded date and recorded time are replaced by dashes (x) when there are no
Time Recorder times currently in memory.
Alarms
The Alarm Mode gives you a choice of four one-time
alarms and one snooze alarm.
Also use the Alarm Mode to turn the Hourly Time Signal
(
SIG) on and off.
• There are five alarms numbered
AL1 through AL4,
and
SNZ. You can configure SNZ as a snooze alarm
only. Alarms
AL1 through AL4 can be used as one-
time alarms only.
• Alarm settings (and Hourly Time Signal settings) are
available in the Alarm Mode, which you enter by
pressing C.
Alarm time (Hour : Minutes)
Alarm number
Home city time
To set an alarm time
1.In the Alarm Mode, use D to scroll through the alarm
screens until the one whose time you want to set is
displayed.
2.After you select an alarm, hold down A until the hour
setting of the alarm time starts to flash, which indicates
the setting screen.
• This operation automatically turns on the alarm.
3.Use C to move the flashing between the hour and
minute settings.
4.While a setting is flashing, use D (+) and B (–) to
change it.
AL1 AL2 AL3
SIG SNZ AL4
5. Press A to exit the setting screen.
• When setting the alarm time using the 12-hour format, take care to set the time
correctly as a.m. (A indicator) or p.m. (P indicator).
Alarm Operation
The alarm tone sounds at the preset time for 10 seconds, regardless of the mode the
watch is in. In the case of the snooze alarm, the alarm operation is performed a total
of seven times, every five minutes, or until you turn the alarm off.
• Pressing any button stops the alarm tone operation.
• Performing any one of the following operations during a 5-minute interval between
snooze alarms cancels the current snooze alarm operation.
Displaying the Timekeeping Mode setting screen
Displaying the
SNZ
setting screen
To test the alarm
In the Alarm Mode, hold down B to sound the alarm.
To turn an alarm on and off
1.In the Alarm Mode, use D to select an alarm.
2.Press B to toggle it on and off.
• Turning on a one-time alarm (
AL1, AL2, AL3,
AL4) displays the alarm on indicator on its Alarm
Mode screen. Turning on the snooze alarm (
SNZ)
displays the alarm on indicator and snooze alarm
indicator on its Alarm Mode screen.
• In all modes, the alarm on indicator is shown for any
alarm that is currently turned on. When the snooze
alarm is on, the snooze alarm indicator is displayed in all
modes.
• The alarm on indicator flashes while the alarm is
sounding.
• The snooze alarm indicator flashes during the 5-minute
intervals between alarms.
Snooze alarm indicator
Alarm on indicator
To turn the Hourly Time Signal on and off
1.In the Alarm Mode, use D to select the Hourly Time
Signal (
SIG
).
2.Press B to toggle it on (Hourly Time Signal on
indicator displayed) and off (Hourly Time Signal on
indicator not displayed).
• The Hourly Time Signal on indicator is displayed in all
modes when the Hourly Time Signal is turned on.
Hourly time signal
on indicator
Stopwatch
The stopwatch lets you measure elapsed time, split times,
and two finishes.
• The display range of the stopwatch is 23 hours, 59
minutes, 59.99 seconds.
• The stopwatch continues to run, restarting from zero
after it reaches its limit, until you stop it.
• Exiting the Stopwatch Mode while a split time is frozen
on the display clears the split time and returns to
elapsed time measurement.
• The stopwatch measurement operation continues even
if you exit the Stopwatch Mode.
• All of the operations in this section are performed in the
Stopwatch Mode, which you enter by pressing C.
1/100 second
Hours
Home city time
Seconds
Minutes
D
Start Stop
Elapsed Time
➤
Re-start Clear
D
➤
Stop
D
➤
D
➤
B
Split Time
D
Start Split
➤
Split release
Clear
B
➤
Stop
B
➤
D
➤
B
Two Finishes
D
Start Split
➤
Stop
Clear
B ➤
Split release
D
➤
B
➤
B
First runner
finishes.
Display time of
first runner.
Second runner
finishes.
Display time of
second runner.
To measure times with the stopwatch
(SPL displayed)
Timekeeping
Use the Timekeeping Mode to set and view the current time and date. This section
also explains how to manually set the current date and time.
• All of the operations in this section are performed in the Timekeeping Mode, which
you can enter by pressing C.
• In the Timekeeping Mode, press D to display the Last Signal screen.
Last Signal Screen
▲
Press D.
Day of week
Month – Day
Hour : Minutes Seconds
PM
indicator
▲
Current Time Screen
Setting the Time and Date Manually
Make sure you select your Home City code before you change the current time and
date settings. World Time Mode times are all displayed in accordance with the
Timekeeping Mode settings. Because of this, World Time Mode times will not be
correct if you do not select the proper Home City code before setting the time and
date in the Timekeeping Mode.
• When setting the time and date, you can also configure settings for the transmitter,
your Home City code (the code for the city where you normally use the watch),
summer time (Daylight Saving time or DST), the 12/24-hour format, and power
saving on/off.
To set the time and date manually
1.In the Timekeeping Mode, hold down A until the city
code setting starts to flash, which indicates the setting
screen.
2.Use A or C to move the flashing in the sequence
shown below to select other settings.
DST
Transmitter
Mode
Seconds
Hour Minutes
12/24-Hour
Format
Day
Power
Saving
Month Year
Press C.
City Code
C
C
Press A.
City/Transmitter
Settings
Time/Date
Settings
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
3. When the setting you want to change is flashing, use B and/or D to change it as
described below.
Screen:
To do this:
Change the city code
Change the transmitter mode (qvtA,
DCF, MSF, or OFF)
Toggle between Daylight Saving
Time (
ON) , Standard Time (OFF),
or Auto DST (
AUtO)
Do this:
Use D (east) and B (west).
Press D.
Press D.
City/Transmitter Settings
• See “City Code Table” for a complete list of available city codes.
• The transmitter mode setting is always OFF and cannot be changed whenever the
city code setting is anything other than
LON, PAR, BER, or ATH.
qvtA
BER
DST
AUtO
4. Use A to exit the setting screen.
• If a City/Transmitter Setting screen is displayed, press A twice.
• If a Time/Date Setting screen is displayed, press A once.
Note
• The “Transmitter Mode” setting specifies the time calibration signal transmitter mode,
or turns auto receive off. See “Transmitters” for more information.
Screen:
To do this:
Toggle between 12-hour (12H) and
24-hour (24H) timekeeping
Reset the seconds to 00
Change the hour or minutes
Change the year, month, or day
Toggle power saving on (ON) and off
(
OFF)
Do this:
Press D.
Press D.
Use D (+) and B (–).
Use D (+) and B (–).
Press D.
Time/Date Settings
12H
P
10:58 50
'04
6x30
PS
ON
• Auto DST (AUtO) can be selected only while LON, PAR, BER, or ATH is selected
as the Home City code. For more information, see “Daylight Saving Time (DST)” below.