Filter
Top Products
Operation Guide 2753 3333
2
To adjust the analog time
1.In the Timekeeping Mode, press C five times to enter
the Hand Setting Mode.
2.Hold down A until the current digital time starts to
flash, which indicates the setting screen.
3. Use D and B to adjust the analog setting as
described below.
l
l
l
l
l
l
l
l
l
l
l
l
Move the hand setting a
long way forward at high
speed
• While holding down D to move the hands at
high speed, press B to lock the high-speed
hand movement.
• To stop the hand movement, press any
button.
• Hand movement stops automatically if the hour
hand makes one full (12-hour) revolution.
4. Press A to exit the setting screen.
• The minute hand will be adjusted slightly to match the seconds when you exit the
setting screen.
• To return to the Timekeeping Mode, press C.
When you want to do this:
Move the hand setting
forward 20 seconds
Move the hand setting a short
way forward at high speed
Perform this button operation:
• Press D.
• Hold down D.
• Release D when the hands reach the setting
you want.
World Time
The World Time Mode digitally displays the current time in
30 cities (29 time zones) around the world.
• Pressing A in the World Time Mode causes the
applicable city code to appear on the digital display for
about one second.
• If the current time shown for a city is wrong, check your
Home City time settings and make the necessary
changes.
• All of the operations in this section are performed in the
World Time Mode, which you enter by pressing C.
City code
Current time in the
selected city code
Mode indicator
To view the time in another city
While in the World Time Mode, press D to scroll through the city codes (time zones)
to the east or B to scroll to the west.
• For full information on city codes, see the “City Code Table”.
To toggle a city code time between Standard Time and Daylight Saving Time
1.In the World Time Mode, use B and D to display the
city code (time zone) whose Standard Time/Daylight
Saving Time setting you want to change.
• Pressing A in the World Time Mode causes the
applicable city code to appear on the digital display for
about one second.
2.Hold down A to toggle Daylight Saving Time (DST
indicator displayed) and Standard Time (DST indicator
not displayed).
DST indicator
• Note that you cannot use the World Time Mode to change the DST setting of the
Home City code you currently have selected in the Timekeeping Mode. See “Daylight
Saving Time (DST)” for information about turning the Home City code DST setting
on and off.
• Note that you cannot switch between Standard Time and Daylight Saving Time while
GMT is selected as the city code.
• The DST indicator will appear on the display whenever you display a city code for
which Daylight Saving Time is turned on.
• Note that the DST/Standard Time setting affects only the currently displayed city
code. Other city codes are not affected.
Alarms
You can set five independent daily alarms. When an alarm
is turned on, the alarm tone sounds when the alarm time
is reached.
You can also turn on an Hourly Time Signal that causes
the watch to beep twice every hour on the hour.
• The alarm number (
A1 through A5) indicates an alarm
screen.
00 is shown for the alarm time when the Hourly
Time Signal screen is on the display.
• All of the operations in this section are performed in the
Alarm Mode, which you enter by pressing C.
Mode indicator
Alarm
number
Alarm time
(Hour : Minutes)
Module 2753
Module 3333
Alarm number
Mode
indicator
Alarm time (Hour : Minutes)
To set an alarm time
1.In the Alarm Mode, use D to scroll through the alarm
screens until the one whose time you want to set is
displayed.
2.Hold down A until the hour digits of the alarm time
start to flash, which indicates the setting screen.
• This automatically turns on the alarm.
3. Press C to move the flashing between the hour and minute settings.
4. While a setting is flashing, use D (+) and B (–) to change it.
• When setting the alarm time using the 12-hour format, take care to set the time
correctly as a.m. (no indicator) or p.m. (P indicator).
5. Press A to exit the setting screen.
A1 A2 A3
00 A5 A4
l
l
l
l
l
l
l
l
l
l
l
l
Hourly time signal
on indicator
Alarm on
indicator
Alarm Operation
The alarm sounds in all modes at the preset time for about 10 seconds, or until you
stop it by pressing any button.
To test the alarm
In the Alarm Mode, hold down B to sound the alarm.
To turn an alarm and the Hourly Time Signal on and off
1. In the Alarm Mode, use D to select an alarm or the Hourly Time Signal.
2. When the alarm or the Hourly Time Signal you want to set is selected, press B to
turn it on and off.
Indicates alarm is ON.
Indicates Hourly Time Signal is ON.
• The alarm on indicator (
) and the Hourly Time Signal on indicator ( ) are shown
on the display in all modes while these functions are turned on.
• If any alarm is on, the alarm on indicator is shown on the display in all modes.
Countdown Timer
You can set the countdown timer within a range of one to
60 minutes. An alarm sounds when the countdown
reaches zero.
• You can also select auto-repeat, which automatically
restarts the countdown from the original value you set
whenever zero is reached.
• All of the operations in this section are performed in the
Countdown Timer Mode, which you enter by pressing
C.
To set the countdown start time
1.While the countdown start time is on the display in the
Countdown Timer Mode, hold down A until the current
countdown start time starts to flash, which indicates the
setting screen.
Minutes Seconds
Mode indicator
Number
of repeats
Module 2753
Mode
indicator
Module 3333
Minutes Seconds
• If the countdown start time is not displayed, use the procedure under “To use the
countdown timer” to display it.
2. Press C to move the flashing in the sequence shown below to select other
settings.
3. While a setting is flashing, use D (+) and B (–) to change it.
• See “To turn auto-repeat on and off” below for details on the auto-repeat setting.
4. Press A to exit the setting screen.
Minutes
Auto-
repeat
To use the countdown timer
Press D while in the Countdown Timer Mode to start the countdown timer.
• When the end of the countdown is reached and auto-repeat is turned off, the alarm
sounds for 10 seconds or until you stop it by pressing any button. The countdown
time is automatically reset to its starting value after the alarm stops.
• Press D while a countdown operation is in progress to pause it. Press D again to
resume the countdown.
• To completely stop a countdown operation, first pause it (by pressing D), and then
press B. This returns the countdown time to its starting value.
To turn auto-repeat on and off
1.While the countdown start time is on the display in the
Countdown Timer Mode, hold down A until the current
countdown start time starts to flash, which indicates the
setting screen.
2.Press C to move the flashing to the auto-repeat
setting.
3.Press D to turn auto-repeat on (
displayed) and
off (
displayed).
4.Press A to exit the setting screen.
• When auto-repeat is turned on, the alarm sounds and
countdown starts again whenever the countdown
reaches zero. You can stop the countdown by pressing
D, and manually reset to the countdown start time by
pressing B.
• Auto-repeat timing repeats up to nine times.
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l