Filter
Top Products
USER’S GUIDE 2512
3
Alarms
The Alarm Mode gives you a choice of four one-time
alarms and one snooze alarm. You can select either an
audible beeper or flashing silent alert to let you know
when any of the alarm times is reached.
You can also input reminder text that appears when the
alarm time is reached.
Also use the Alarm Mode to turn the Hourly Time Signal
on and off.
• All of the operations in this section are performed in the
Alarm Mode, which you enter by pressing C .
Alarm time
Alarm on indicator
Alarm screen name/
Reminder text
Alarm name
indicator
To display Alarm Mode screen
In the Alarm Mode, use D to cycle through the alarm screens as shown below.
• The following alarm screen names appear in the center
of the display to indicate the alarm whose screen is
currently displayed.
ALARM1 through ALARM4: One-time alarm screen
SNOOZE: Snooze alarm screen
SIGNAL: Hourly Time Signal screen
• The currently displayed alarm screen is also indicated
by the alarm name indicators along the bottom left of the
watch’s display.
ALARM1
ALARM2
ALARM3 ALARM4
SNOOZE
SIGNAL
Alarm1
Alarm2
Alarm3
Alarm4
Snooze
To set an alarm
1.In the Alarm Mode, use D to select the alarm whose
time you want to set.
2.Press B and the hour setting of the alarm time starts
to flash, which indicates the setting screen.
• Pressing A and D at the same time resets the alarm
time to 12:00 AM, and clears the reminder text in the
upper part of the display (if there is any).
3.Press C to move the flashing in the sequence shown
below to select other settings.
• Selecting the text causes the text input cursor to appear. You can input up to eight
characters of reminder text for each alarm.
• There are eight spaces in the text, so you have to press C eight times to move to
the Hour setting.
MinutesHour
Tex t
4. When the setting you want to change is selected, use A and D to change it.
• While the hour or minute setting is flashing, use D (+) and A (–) to change it.
• When setting the alarm time using the 12-hour format, take care to set the time
correctly as a.m. (no indicator) or p.m. (P indicator).
• When inputting text, use A and D to cycle through characters at the current
cursor location, and C to move the cursor to the right. See “Inputting Text” for
more information.
5. Press B to exit the setting screen.
• If you input reminder text, the text appears in place of the alarm screen name when
you exit the setting screen.
• If the reminder text has more than six characters, it will scroll from right to left
whenever it is displayed.
Alarm Operation
The following table describes the different types of alarm operations that this watch
can perform.
Alarm Operation
Type
Alarm off
Alarm on
Alert on
Description
• Nothing happens when the alarm
time is reached.
• The alarm on indicator and alarm
name indicator flash on the display
for 10 seconds.
• The watch beeps for 10 seconds.
• The alert on indicator and alarm
name indicator flash on the display
for 10 seconds.
• The watch does not beep.
Snooze
indicator
Alert on
indicator
Alarm on indicator
• Press any button to stop the alarm after it starts to sound.
• If any alarm operation (one-time alarm, silent alert, snooze) occurs while a signal
receive operation is in progress, the receive operation is canceled.
• In the case of the snooze alarm, the alarm operation repeats up to seven times
every five minutes until the alarm is turned off.
• If you input reminder text for an alarm, the text appears for one minute in place of
the date on the Timekeeping Mode screen. The text is cleared from the Timekeeping
Mode screen if you change to another mode while it is displayed.
• Alarm operations and the Hourly Time Signal operation are performed in all modes.
To test the alarm
In the Alarm Mode, hold down D to sound the alarm.
To select the alarm operation type
1. In the Alarm Mode, use D to select the screen for the alarm (ALARM1 to
ALARM4, or SNOOZE) whose alarm type you want to select.
2. Press A to cycle through the available settings in the sequence shown below.
• The alarm on indicator (
) and alarm name indicator are displayed for each alarm
(1 through 4, snooze) for which alarm on is selected. The alert on indicator
(
) and alarm name indicator are displayed for each alarm (1 through 4, snooze)
for which alert on is selected.
Alarm onAlarm off
Alert on
• In other modes besides the Alarm Mode, the alarm name indicator is displayed for
each alarm for which alarm on is selected.
• In all modes, the alarm on indicator or alert on indicator is shown for any alarm
(ALARM1 through ALARM4, or SNOOZE) that is currently turned on.
To turn the Hourly Time Signal on and off
1.In the Alarm Mode, use D to select the Hourly Time
Signal (SIGNAL).
2.Press A to toggle it on (SIG displayed) and off (SIG
not displayed).
• The Hourly Time Signal on indicator (SIG) is shown on
the display in all modes while this function is turned on.
Data Memory
You can use the watch’s data memory to store e-mail
addresses, Web page URLs, and other text data.
• All of the operations in this section are performed in the
Data Memory Mode, which you enter by pressing C.
Data Memory Records
Each data memory record can contain up to 63
characters. Records are stored in memory in the
sequence they are created.
• The number of records you can store in data memory
depends on the number of characters that make up
each record. See “Data Memory Management” for more
information.
Remaining memory
To create a new data memory record
1.In the Data Memory Mode, press A and D at the
same time to display the remaining memory screen.
• You do not have to perform the above step if the
remaining memory screen is already on the display.
• If REST 0% is shown for remaining memory, it means
that memory is full. To store another record, you will
first have to delete some of the records stored in
memory.
2.Press B and the flashing cursor appears on the
display, which indicates the setting screen.
3.Use A and D to cycle through characters at the
current cursor location, and C to move the cursor to
the right. See “Inputting Text” for more information.
• If memory becomes full while you are inputting text,
the cursor will jump to the first (leftmost) character of
the text when you press C, instead of advancing to
the right.
Cursor
4.Press B to store your data and return to the data
memory record screen (without the cursor).
• The message SAVE! appears for about two seconds,
followed by a data memory record screen, which shows
the text you just input in the upper part of the display,
and a record number automatically assigned by the
watch in the lower part of the display.
• While the record number is in the lower part of the
display, you can see only six characters of the text in the
record. You can scroll through the text on the screen by
pressing D. See “To recall data memory records” for
more information.
Record number
Text
To recall data memory records
1. In the Data Memory Mode, press A to scroll forward through data memory
records.
• Each press of A advances to the next record and shows its record number and
first six characters of its text.
• Pressing A while the last record in memory is on the display changes to the
remaining memory screen. Pressing A again displays the first record.
2. Press D to scroll through the text on the screen.
• An end mark indicates the end of the text.
▲
First six characters
Pressing D scrolls through the text.
End mark
▲