Filter
Top Products
2307/2335/2355/2357-5
A
D
A
B
C
0
0
OO
0
1
OO
0
1
OO
A
L
D
A
B
C
7OO
RECALL MODE
Recalling data
1. Use C to enter the Recall Mode.
2. Each press of D cycles through the barometric pressure, altitude, and
temperature data in memory. Mode indicators appear to tell you what type
of data is currently displayed.
• Note that measurement units are not indicated on the Recall Mode screens.
• The display shows “- - - - – –” if there is no data.
Deleting Data
While in the Recall Mode, hold down A. The
watch beeps, and the message CLR flashes
on the display to indicate data is about to be
deleted. Keep A depressed for about two
seconds to delete all the measurement data
currently in memory.
• Note that this procedure deletes all
measurement data in memory. You cannot
delete individual records.
E
A
C
D
A
B
C
2
1
5
0
Memory number
1 second
later
▼
Altitude
Recall Mode indicator
L
C
A
ALARM MODE
When the Daily Alarm is turned on, the alarm sounds for 20 seconds at the
preset time each day. Press any button to stop the alarm after it starts to
sound.
When the Hourly Time Signal is turned on, the watch beeps every hour on the
hour.
To set the alarm time
1. Hold down A until the hour digits start to flash on the display. The hour
digits flash because they are
selected
. At this time the alarm is
automatically turned on.
2. Press C to change the selection in the sequence shown below.
Minutes
Hour
3. Press D to increase the number or B to decrease it.
• Holding down either button changes the setting at high speed.
4. After you set the alarm time, press A to return to the Alarm Mode screen.
• The format (12-hour and 24-hour) of the alarm time matches the format you
select for normal timekeeping.
• When setting the alarm time using the 12-hour format, take care to set the
time correctly as morning or afternoon.
To stop the alarm
• Press any button to stop the alarm after it starts to sound.
Hourly time signal on
indicator
1 second
later
▼
Alarm on indicator
Alarm Mode indicator
Alarm time
To turn the Daily Alarm and Hourly Time Signal on
and off
Press D while in the Alarm Mode to change the status of the Daily Alarm and
Hourly Time Signal in the sequence shown below.
• The alarm and hourly time signal indicator is displayed in all modes.
To test the alarm
Hold down D while in the Alarm Mode to sound the alarm.
Both ON
Both OFF
Hourly Time
Signal only
Daily Alarm only
COUNTDOWN ALARM MODE
The countdown alarm can be set within a range of 10 seconds to 60 minutes.
When the countdown reaches zero, an alarm sounds for 10 seconds or until
you press any button.
To set the countdown start time and auto repeat
function on and off
1. Hold down A while in the Countdown Alarm Mode. The minutes setting
flashes on the display because it is
selected
.
2. Press C to change the selection in the sequence shown below.
Minutes Seconds Auto repeat ON/OFF
3. Press D to increase the selected setting or B to decrease it. Holding
down either button changes the setting at high speed.
• The seconds can be set in units of 10 seconds.
• Set 0 minutes, 0 seconds to specify a start time of 60 minutes.
• While the AUTO ON/OFF setting is selected (flashing), press D or B to
toggle auto repeat on and off.
4. After you set the countdown start time and auto repeat ON/OFF setting,
press A to return to the Countdown Alarm Mode screen.
To use the countdown alarm
1. Press D while in the Countdown Alarm Mode to start the countdown
alarm operation.
2. Press D again to stop the countdown alarm operation.
• You can resume a paused countdown alarm operation by pressing D.
3. Stop the countdown alarm and then press B to reset the countdown time
to its starting value.
• When the end of the countdown is reached and auto repeat is off, the alarm
sounds for 10 seconds or until you stop the alarm by pressing any button.
Countdown timing stops and the countdown time is automatically reset to its
starting value after the alarm stops.
• When the end of the countdown is reached while auto repeat is on, the
alarm sounds, but the countdown restarts from the beginning without
stopping. You can stop the countdown by pressing D and manually reset
to the start time by pressing B.
• When the start time is less than one minute and auto repeat is turned on,
the countdown alarm tone sounds for only one second instead of the
normal 10 seconds.
1/10 second
1 second
later
▼
Minutes
Countdown Alarm Mode indicator
Seconds
Auto repeat ON Auto repeat OFF
Auto repeat ON indicator
STOPWATCH MODE
The Stopwatch Mode lets you record elapsed time, split times, and two
finishes. The range of the stopwatch is 59 minutes, 59.99 seconds.
Stopwatch functions are available in the Stopwatch Mode, which you can
enter using C .
S
D
A
B
C
0
0
OO
1 second
later
▼
Stopwatch Mode indicator
1/100 second
Minutes
Seconds
▼
▼
DDB
Stop ClearStart
(a) Elapsed time measurement
(b) Split time measurement
(c) Split time and 1st-2nd place times
▼
▼
DDB
Start Stop Clear
▼
▼
DBB
Start Split release
Clear
Record time of
second runner.
▼
D
▼
B
▼
D
▼
D
Stop
▼
B
Split
▼
B
Split
First runner
finishes.
Re-start
Split release
Stop
Second runner finishes.
Record time of first runner.