Filter
Top Products
Module No. 2235
2235-1
GENERAL GUIDE
• Press C to change from mode to mode.
• Pressing E in any mode besides the Alarm Mode illuminates to the display for about three seconds. The backlight is disabled while a setting screen is on the display.
• If you do not perform any operation for a few minutes while a setting screen (with flashing digits) is on the display, the watch automatically exits the setting screen.
• If you do not perform any operation for a few minutes in any mode besides stopwatch mode, the watch automatically reverts to the normal timekeeping screen.
TIMEKEEPING MODE
Press D to toggle between 12-hour and 24-hour time-
keeping.
• With 12-hour timekeeping, times between midnight and
noon are indicated by A (am), while times between noon
and midnight are indicated by P (pm).
• The A and P indicators do not appear for 24-hour time-
keeping.
• Pressing B plays a melody. To stop a playing melody,
press any button besides E.
• Special melodies play each year on January 1 and De-
cember 25.
• Pressing E while a melody is playing toggles the dis-
play between an animated character and the name of
the melody.
∗
See the “MELODY LIST” for the names of melodies.
• Press E to illuminate the display for about three seconds.
Timekeeping Mode Settings
In addition to settings for the current time and date, the Timekeeping Mode setting
screen also lets you turn button tones and melody play on and off, adjust tones and
melody volume, and adjust display contrast.
To make Timekeeping Mode settings
1.While in the Timekeeping Mode, hold down A until the seconds digits flash on the
display, indicating the setting screen.
2.Press C to move the flashing in the sequence shown below. Press E to move
the flashing in the opposite direction.
Seconds DST Hour Minutes Year
Contrast
(CNT)
Volume
(VOL)
Sound
(SOUND)
MonthDay
Press . Press .
3.While the seconds setting is selected (flashing), press
D or B to reset it to 00.
• If you press D or B while the seconds setting is in the
range of 30 to 59, the seconds are reset to 00 and 1 is
added to the minutes. If the seconds setting is in the
range of 00 to 29, the minutes count is unchanged.
• While the DST
∗
(Daylight Saving Time) setting is se-
lected, press D or B to toggle it on and off.
• DST indicator 1 is displayed in the Timekeeping Mode
setting screen only when the DST setting is selected. It
shows ON when the DST setting is on, and OFF when
the DST setting is off.
• DST indicator 2 is displayed in the Timekeeping Mode,
Day Counter Mode and Alarm Mode when the DST set-
ting is turned on.
∗
Daylight Saving Time (DST), which is also sometimes
called “summer time” advances the time for one hour, as
is the custom in some areas during the summer. Re-
member that not all countries or even local areas use
Daylight Saving Time.
• While the SOUND (button tones) setting is selected, press D or B to turn the
beep and musical tone on and off, as shown below.
• Changing the SOUND also changes the Hourly Time Signal tones.
Beep
Musical tone
Off
Press . Press .
• While the VOL setting is selected, press D or B to toggle it between loud and
soft.
Loud
Soft
Press or .
• While the CNT setting is selected, press D to make the display darker, or B to
make it lighter.
• While any other setting is selected (flashing), press D to increase it or B to de-
crease it. Holding down either button changes the setting at high speed.
Alarm Mode Stopwatch Mode Memo Mode
Timekeeping Mode Day Counter Mode
Press C.
4.After you make the settings you want, press A to exit the setting screen.
• The day of the week is automatically set in accordance with the date.
• The date can be set within the range of January 1, 2000 to December 31, 2039.
• The watch’s built-in full automatic calendar automatically makes allowances for dif-
ferent month lengths and leap years.
Once you set the date, there should be no reason to change it except after the
replacement of the watch’s battery.
ABOUT THE BACKLIGHT
About the Auto Light Switch Function
When the auto light switch function is turned on, the backlight automatically turns on
for two seconds under the conditions described below. Avoid wearing the watch on
the inside of your wrist. Doing so causes the auto light switch to operate when not
needed, which shortens battery life.
Moving the watch to a position that is parallel to the ground and then tilting it
towards you approximately 40 degrees causes the backlight to illuminate.
Month
Day of week
Day
PM indicator
Hour
Minutes
Seconds
DST indicator 2
DST indicator 1
DST indicator
2
Parallel to ground
40
°
• The backlight may not illuminate if the face of the watch is more than 15 degrees off
parallel to the left or right. Make sure that the back of your hand is parallel to the
ground.
• Static electricity or magnetic force can interfere with proper operation of the auto
light switch function. If the auto backlight does not illuminate, try moving the watch
back to the starting position (parallel with the ground) and then tilt it back toward
you again. If this does not work, drop your arm all the way down so it hangs at your
side, and then bring it back up again.
• Under certain conditions the backlight may not light until about one second or less
after turning the face of the watch towards you. This does not necessarily indicate
malfunction of the backlight.
To switch the auto light switch function on and off
In the Timekeeping Mode, hold down D for two seconds to turn the auto light switch
function on and off.
Auto light switch
indicator
ON OFF
• The auto light switch indicator is shown on the display in all modes while the auto
light switch function is on.
• In order to protect against running down the battery, the auto light switch function is
automatically turned off approximately three hours after you turn it on. Repeat the
above procedure to turn the auto light switch function back on if you want.
• Pressing E in any mode besides the Alarm Mode illuminates the display for about
three seconds, regardless of the auto light switch’s on/off setting.
Caution
• The backlight of this watch employs an electro-luminescent (EL) light, which loses
its illuminating power after very long term use.
• Frequent use of the backlight shortens the battery life.
• The watch emits an audible sound whenever the display is illuminated. This is
because the EL light vibrates slightly when lit. It does not indicate malfunction of
the watch.
Parallel to ground
More than 15 degrees
too high
More than 15 degrees
too low
Hold down D.