Filter
Top Products
1934/1935-2
8.When the character you want is at the cursor position, press
DD
DD
D to move the cursor
to the right.
9.Repeat steps 7 and 8 until you complete number input.
• You can input up to 12 digits in the number field.
10.After inputting your data, press
CC
CC
C to store it.
• When you press
CC
CC
C to store data, the watch takes a few seconds to sort memory
data. After the sort operation is complete, the watch returns to the normal Data
Bank Mode (without the cursor).
• Unused spaces at the end of the name and number fields are automatically filled in
with “ t” whenever the number of characters you input in these fields is less than
the allowable maximum (8 characters for the name, 12 digits for the number). These
filler characters appear on the display whenever you recall data.
• If you do not perform any button operation for a few minutes while the cursor is on
the display, the watch automatically returns to the normal Data Bank Mode (without
the cursor).
To recall Data Bank data
1.In the Data Bank Mode, press
BB
BB
B to scroll through stored data items.
• Holding down
BB
BB
B scrolls through the data at high speed.
• Only name data appears when you are scrolling through stored data items.
2.Press
CC
CC
C to toggle the screen between the name and number data.
• The name and number scroll from right to left on the screen. A separator (
<
) is
inserted between the last character and first character of the data.
To edit Data Bank data items
1.In the Data Bank Mode, scroll through the data items and display the one you want
to edit.
2.Hold down
CC
CC
C until the first character of the name starts to flash on the display.
3.Use
DD
DD
D to move the flashing to the character you want to change.
4.Use
AA
AA
A and
BB
BB
B to change character.
• For details on inputting characters, see “To input new Data Bank data” (steps 3 for
name input and 7 for number).
5.After making the changes that you want, press
CC
CC
C to store them and return to the
Data Bank Mode.
To delete Data Bank data
1.In the Data Bank Mode, scroll through the data items and display the one you want
to delete.
2.Hold down
CC
CC
C until the first character of the name starts to flash on the display.
3.Press
AA
AA
A and
BB
BB
B at the same time to delete the data item.
• At this time the cursor appears on the display, ready for input.
4.Input data or press
CC
CC
C to return to the Data Bank Mode.
ALARM MODE
When the Daily Alarm is turned on, the alarm sounds for
20 seconds at the preset time each day. Press any button
to stop the alarm after it starts to sound.
When the Hourly Time Signal is turned on, the watch beeps
every hour on the hour.
• The alarm sounds whenever the time displayed in the
Timekeeping Mode reaches the alarm time and the Hour-
ly Time Signal sounds at the top of each hour, regard-
less of whether you are using the Home Time screen or
Dual Time screen.
• Note that switching between the Home Time and Dual
Time screen in the Timekeeping Mode has no effect on
the Daily Alarm time setting. If you set an alarm time of
4:00 pm for your Home Time and then change to the
Dual Time screen, the Daily Alarm will start to sound
when the Dual Time reaches 4:00 pm.
To set the alarm time
1.Hold down
CC
CC
C while in the Alarm Mode until the hour digits start to flash on the
display. The hour digits flash because they are
selected
.
• This operation will turn the Daily Alarm on automatically.
2.Press
DD
DD
D to change the selection in the following sequence.
3.Press
BB
BB
B to increase the selected digits or
AA
AA
A to decrease them. Holding down
either button changes the selection at high speed.
• The format (12-hour and 24-hour) of the alarm time matches the format you select
for normal timekeeping.
• When setting the alarm time using the 12-hour format, take care to set the time
correctly as morning (no indicator) or afternoon (PM).
4.After you set the alarm time, press
CC
CC
C to return to the Alarm Mode.
• If you do not operate any button for a few minutes while a selection is flashing, the
flashing stops and the watch goes back to the Alarm Mode automatically.
To turn the Daily Alarm and Hourly Time Signal on and off
Press
BB
BB
B while in the Alarm Mode to change the status of the Daily Alarm and Hourly
Time Signal in the following sequence.
[Alarm ON Indicator/Hourly Time Signal ON Indicator]
To test the alarm
Hold down
BB
BB
B while in the Alarm Mode to sound the alarm.
Hour Minutes
Hourly Time
Signal Only
Daily Alarm
Only
Both OFFBoth ON
STOPWATCH MODE
The Stopwatch Mode lets you measure elapsed time, split
times, and two finishes. The range of the stopwatch is 59
minutes, 59.99 seconds.
(a) Elapsed time measurement
Start
Stop Re-start Stop Clear
Start
Split Split release Stop Clear
Start
Split Stop Split release Clear
(b) Split time measurement
(c) Split time and 1st-2nd place times
First runner
finishes.
Second runner
finishes.
Record time of
first runner.
Record time of
second runner.
BACKLIGHT
In any mode, press
AA
AA
A to illuminate the display for about two seconds.
•
The portion of the display illuminated by the backlight depends on the watch model.
With some models, smaller indicators may not be made visible by backlight illumina-
tion. Be especially careful when checking the Home Time and Dual Time indicators.
• The backlight of the watch employs an electro-luminescent (EL) light, which loses
illuminating power after very long use.
• The illumination provided by the backlight may be hard to see when viewed under
direct sunlight.
• The watch will emit an audible sound whenever the display is illuminated. It does
not indicate malfunction of the watch.
• The backlight automatically stops illuminating whenever an alarm sounds.
• Pressing any button besides
AA
AA
A while the backlight is lit turns it off.
AUTO DISPLAY FUNCTION
The Auto Display function of this watch continually chang-
es the contents of the digital display. Note that you can-
not use any of the watch’s other functions (except for back-
light) while the Auto Display function is operating.
To turn the Auto Display off
Hold down
DD
DD
D for about three seconds until the watch
beeps.
To turn Auto Display on
Hold down
DD
DD
D for about three seconds until the watch
beeps.
Note
The Auto Display function cannot be performed while you are making settings (i.e.
while digits or other settings are flashing on the display).
About On-screen Button Labels (Module 1934 only)
This watch features on-screen button labels that indicate the function of each button.
You can use the following procedure to turn these labels on and off.
To turn on-screen button labels on and off
While the Auto Display function is turned on, press
CC
CC
C to toggle the on-screen button
labels on and off.
• The on-screen button label setting you select remains in effect even when you turn
off the Auto Display function.
[Name Screen]
[Number Screen]
Press
CC
CC
C.
NAME indicator TEL indicator
Hour : Minutes
Mode indicator
Alarm on indicator
Hourly time signal
on indicator
Mode indicator
Minutes
Seconds
1/100 second
On-screen button labels