Filter
Top Products
1803-2
More than 15 degrees
too high
More than 15 degrees
too low
Parallel to ground
• The backlight turns off in about two seconds, even if you keep the watch
pointed towards your face.
• The backlight may not light if the face of the watch is more than 15 degrees
off the parallel as shown below. Make sure that the back of your hand is
parallel to the ground.
• Static electricity or magnetic force can interfere with proper operation of the
auto light switch. If the backlight does not light, try moving the watch back to
the starting position (parallel with the ground) and then tilt it back toward you
again. If this does not work, drop your arm all the way down so it hangs at
your side, and then bring it back up again.
• Under certain conditions the backlight may not light until about one second
or less after turn the face of the watch towards you. This does not necessarily
indicate malfunction of the backlight.
Warning!
• Never try to read your watch when mountain climbing or hiking in areas
that are dark or in areas with poor footing. Doing so is dangerous and
can result in serious personal injury.
• Never try to read your watch when running where there is danger of
accidents, especially in locations where there might be vehicular or
pedestrian traffic. Doing so is dangerous and can result in serious
personal injury.
• Never try to read your watch when riding on a bicycle or when operating
a motorcycle or any other motor vehicle. Doing so is dangerous and
can result in a traffic accident and serious personal injury.
• When you are wearing the watch, make sure that its auto light switch is
turned off before riding on a bicycle or operating a motorcycle or any
other motor vehicle. Sudden and unintended operation of the auto light
switch can create a distraction, which can result in a traffic accident
and serious personal injury.
To turn the auto light switch on and off
In the Timekeeping Mode, hold down D for one second to turn the auto light
switch on (
AUTO
displayed) and off (
AUTO
not displayed).
• Frequent use of the auto light switch greatly reduces the charge of the storage
battery. If you use the auto light switch often, be sure to leave the watch
where it is exposed to sunlight during the day time so it can recharge the
storage battery. 10 minutes exposure to sunlight provides enough of a charge
for about 10 to 20 auto light switch operations.
• The
AUTO
indicator is on the display in all modes while the auto light switch
is turned on.
A
CD
L
B
A
CD
L
B
TELEMEMO MODE
The Telememo Mode lets you store up to 30
pairs of name and telephone number data.
Data is automatically sorted based on the
characters of the name. You can recall data
by scrolling through it on the display.
• See the “CHARACTER LIST” at the back
of this manual for details on how the watch
sorts data.
• If there is no data stored in the Telememo
Mode, the message
NO-DATA
appears following the remaining memory
screen.
• The data item on the display when you exit
the Telememo Mode appears first the next
time you enter the Telememo Mode.
• In the Telememo Mode, press L to
illuminate the display. Pressing L
illuminates the display even while you are
inputting data.
To input new Telememo data
1. In the Telememo Mode, press B and D at
the same time to display the new data screen.
• The new data screen is the one that is blank
(contains no name and telephone number).
• If the message
FULL appears in the text
area of the display, it means that memory is
full. To store more data, you will first have to
delete some of the data stored in memory.
2. Hold down A until the flashing cursor
appears in the text area of the display.
3. Use B and D to change the character at
the cursor position in the text area. The
character changes in the following sequence.
Name
Mode indicator
Telephone number
Remaining
memory
Cursor
Text Area
Number Area
[New Data Screen]
Press D
Press B
. -/
:
Press D
Press B
(space)
0 to 9
A to Z
• Holding down either button changes the character at high speed.
4. When the character you want is at the cursor position, press C to move the
cursor to the right.
5. Repeat the steps 3 and 4 until your text is complete.
• You can input up to eight characters for the name.
6. After you input a name, use C to move the cursor to the number area.
• The text area can hold up to eight characters. When the cursor is located at
the eighth space of the text area, moving the cursor to the right causes it to
jump down to the first digit in the number area. When the cursor is at the 12th
digit of the number area, moving it to the right causes it to jump back up to
the first character of the text area.
7. Use B and D to change the character (hyphen, number, or space) at the
cursor position in the number area. The character changes in the following
sequence.
x
(space)
0 to 9
• Holding down either button changes the character at high speed.
8. When the character you want is at the cursor position, press C to move the
cursor to the right.
9. Repeat steps 7 and 8 until you complete number input.
• You can input up to 12 digits for the number.
10.After inputting your data, press A to store it.
• When you press A to store data, the message
SORT appears on the
display for a few seconds. After the sort operation is complete, the cursor
appears in the text area, ready for input a new Telememo data item.
11.Input more data (staring from step 3) or press A again to return to the
Telememo Mode data screen (without the cursor).
• If you do not perform any button operation for few minutes while the cursor is
on the display, the watch automatically returns to the Telememo Mode data
screen.
• The text area of the display can show only five characters at a time, so longer
text scrolls continuously from right to left.
Caution
The following causes all data stored in memory to be deleted. Be sure to
always keep separate written copies of all important data.
Malfunction or repairs/Dead battery/Battery replacement
In no event will CASIO be liable for loss of data or any damages arising out
of such loss.
To recall Telememo data
In the Telememo Mode, press D to scroll forward through stored data items or
B to scroll in reverse.
• Holding down either button scrolls through the data at high speed.
To edit Telememo data items
1. In the Telememo Mode, scroll through the data items and display the one
you want to edit.
2. Hold down A until the flashing cursor appears in the text area of the display.
3. Use C to move the flashing cursor to the character you want to change.
4. Use B and D to change the character.
• For details on inputting characters, see “To input new Telememo data” (steps
3 for name input and 7 for number).
5. After making the changes that you want, press A to store them and return
to the Telememo Mode data screen.
To delete Telememo data
1. In the Telememo Mode, scroll through the data items and display the one
you want to delete.
2. Hold down A until the flashing cursor appears in the text area of the display.
3. Press B and D at the same time to delete the data item.
• At this time the cursor appears in the text area, ready for input.
4. Input data or press A to return to the Telememo Mode data screen.