Casio 1675-1 Watch User Manual


 
1675-6
Deleting Data
Delete data in the Recall Mode. The actual procedure you should use to
delete data depends on the type of data it is.
To delete auto memory data
The following procedure deletes an entire set (from start measurement to end
measurement) of auto memory data.
Important!
You cannot delete data while an auto memory
measurement is in progress (“AUTO” flashing
on the display).
1. In the Recall Mode, display the start data
of the set of auto memory data that you
want to delete.
2. To clear the data, hold down A until the
watch emits a beep (and until “CLR” stops
flashing on the display).
To delete manual memory, maximum, and minimum data
1. In the Recall Mode, display the data that you want to delete.
2. To clear the data, hold down A until the watch emits a beep (and until
“CLR” stops flashing on the display).
ERROR WARNING FUNCTION
This watch is designed to automatically stop taking measurements when
there is a sensor malfunction, when battery power drops below a certain
level, or when battery voltage is decreased below a certain level due to very
cold temperatures.
Sensor malfunction
Low battery
Important!
If the sensor is malfunctioning when it comes time for an barometric
pressure measurement to be taken, the barometric pressure value appears
as “– – – –” on the display and the corresponding point on the barometric
pressure graph is left blank.
There may be cases where the “ERROR” or “BATTERY” message is
cleared once you change modes. In this case, you can continue using the
watch normally unless the error warning message reappears.
Whenever there is a sensor malfunction, be sure to take the watch to an
authorized CASIO distributor or Service Center as soon as possible. If the
appearance of the “BATTERY” message is caused by extremely low
temperature, the message should clear from the display when normal
temperature returns. It is recommended, however, that you still have the
watch checked by an authorized CASIO distributor or Service Center.
C
D
BA
A
°
C
m
RECALL
AUTO
(
Auto Memory Start Display
)
Auto memory
measurement indicator
ERROR
P
°
C
m
ALTI
AUTO
ERROR
P
°
C
hPamb
ERROR
During Barometric Pressure
Measurement
During Altitude Measurement
BATTERY
P
°
C
m
ALTI
AUTO
BATTERY
P
°
C
hPamb
BATTERY
During Barometric Pressure
Measurement
During Altitude Measurement
ALARM FUNCTIONS
When the Daily Alarm is on, the alarm sounds
for 20 seconds at the preset time each day.
Press any button to stop the alarm after it
starts to sound.
When the Hourly Time Signal is on, the watch
beeps every hour on the hour.
To set the alarm time
1. Use C to enter the Alarm Mode.
2. Hold down A until the hour digits flash on the display. The hour digits
flash because they are
selected
.
At this time, the alarm is automatically switched on.
3. Press C to change the selection in the following sequence.
4. Press D to increase the selected digits. Holding down D changes the
selection at high speed.
The format (12-hour and 24-hour) of the alarm time matches the format you
select for normal timekeeping.
When setting the alarm time using the 12-hour format, take care to set the
time correctly as morning (A) or afternoon (P).
5. After you set the alarm, press A to return to the Alarm Mode.
To switch the Daily Alarm and Hourly Time Signal on and off
Press D while in the Alarm Mode to change the status of the Daily Alarm and
Hourly Time Signal in the following sequence.
[Alarm ON Indicator / Hourly Time Signal ON Indicator]
To test the alarm
Hold down D while in the Alarm Mode to sound the alarm.
STOPWATCH FUNCTIONS
The Stopwatch Functions let you record
elapsed time, split times, and two finishes.
The range of the stopwatch is 23 hours, 59
minutes, 59.99 seconds.
Stopwatch functions are available in the Stop-
watch Mode, which you can enter using C.
C
D
BA
A
Both ON
Both OFF
Hourly Time
Signal only
Daily Alarm only
Mode indicator
Minutes
Hour
Alarm on
indicator
Hourly time signal
on indicator
Hour Minutes
C
D
BA
Minutes
Hours
1/100 second
Seconds
(a) Elapsed time measurement
(b) Split time measurement
(c) Split time and 1st-2nd place times
DDDDB
StopRe-start ClearStart Stop
DB
B
DB
Start Split Split release Stop Clear
BDDBB
Start Split releaseStopSplit Clear
First runner
finishes.
Second runner finishes.
Record time of first runner.
Record time of
second runner.
Mode indicator