Filter
Top Products
Operation Guide 1138 1173
2
POWER
TV/VCR
STOP
PLAY
TV
P
To use the remote control functions
1. In the Timekeeping Mode, press A to select either the
TV Mode (
TV
indicator shown on the display) or Video
Mode (
indicator shown on the display).
2. Point the Signal Emitter (red window) at your TV or tape
deck and use the buttons on the right side and the
bottom of the watch to perform the operation that you
want (see the table below).
• Each time you perform an operation, an indicator
appears on the display to show which operation is being
performed.
A
C
B
Indicator
Signal Emitter
TV mode
indicator
TV Mode Video Mode
Operation
Switches power on and off
Switches between TV and
video function
No function
No function
Changes to the next higher
channel
Increases volume
Decreases volume
Changes to the next lower
channel
Indicator
Operation
Switches power on and off
Switches between TV and
video function
Stops tape transport
Starts tape playback
Changes to the next higher
channel
Starts fast forward operation
Start rewind operation
Changes to the next lower
channel
Indicator
Button
POWER
TV/VCR
STOP/
PLAY/
/+
▲/
▼/
/–
Note
• This watch is equipped with buttons that cover as wide a range of remote control
functions as possible. Note, however, that if your TV or tape deck is not equipped
with some of these functions, nothing will happen when you press the corresponding
button on this watch.
• For televisions that do not have a TV/video switching function, pressing the TV/VCR
button may switch teletext, etc. on and off.
Troubleshooting Guide
Problem: Remote control functions do not work at all.
• Possible Cause: Use of the wrong mode (TV/Video)
Action: Make sure the watch is in the TV Mode when you are trying to control a
TV, or in the Video Mode when you are trying to control a video tape
deck. See “About the Timekeeping sub-modes” for details on changing
modes. You cannot control any other remote control device (besides a
TV or video tape deck) using this watch.
• Possible Cause: Wrong manufacturer code
Action: You must set the correct manufacturer code for the type of TV or video
tape deck you are trying to control. See “To set the manufacturer code”.
• Possible Cause: The path between the signal emitter and TV/video tape deck is
blocked or too long (more than 16 feet/5 meters).
Action: Make sure that the path between the watch’s signal emitter and the
signal receiver on your TV or tape deck is not blocked by clothing, your
hand, furniture, etc. Reduce the distance between the signal emitter and
TV/video tape deck if necessary.
Problem: Some remote control functions do not work.
• Possible Cause: Too much distance between the watch and TV/video tape deck,
or improper pointing of the watch’s signal emitter.
Action: The distance between the watch and TV/video tape deck should be less
than 16 feet/5 meters. Also, make sure that the signal emitter is pointing
directly at the TV/video tape deck when you are performing a remote
control function.
• Possible Cause: Use of button on the watch for which the TV/video tape deck does
not have a corresponding function.
Action: Some TV or tape deck models may not have functions that correspond to
the functions provided on the watch.
Problem: Video deck functions do not work at all.
• Possible Cause: Your video tape deck might have a dual code (A Code/B Code or
Video 1/Video 2) remote control receiver.
Action: Try switching the setting (between A Code/B Code or Video 1/Video 2)
on your video tape deck until you find the correct setting for use with the
watch.
Stopwatch Mode
The Stopwatch Mode lets you measure elapsed time, split
times, and two finishes. The range of the stopwatch is 23
hours, 59 minutes, 59 seconds.
(a) Elapsed time measurement
(b) Split time measurement
(c) Split time and 1st-2nd place times
A
C
B
Mode indicator
Hours
Minutes
Seconds
A
Start
▼
A
▼
A
▼
A
▼
B
Re-startStop Stop Clear
A
Start
▼
B
▼
B
▼
A
▼
B
Split Stop ClearSplit release
A
Start
▼
B
▼
A
▼
B
▼
B
Split ClearStop Split release
Second runner
finishes.
Record time of
first runner.
First runner
finishes.
Record time of
second runner.
Alarm Mode
When the Daily Alarm is switched on, the alarm sounds for
20 seconds at the preset time each day. Press any button
to stop the alarm after it starts to sound.
When the Hourly Time Signal is switched on, the watch
beeps every hour on the hour.
To set the alarm time
1.Hold down B while in the Alarm Mode until the hour
digits start to flash on the display. The hour digits flash
because they are
selected
.
• This operation will switch the Daily Alarm on
automatically.
A
C
B
Hour
Minutes
Alarm on
indicator
Mode indicator
Hourly time signal
on indicator
2.Press ▲ to change the selection in the following
sequence.
3. Press
to increase the selected digits. Holding down increases the selection at
high speed.
• The format (12-hour and 24-hour) of the alarm time matches the format you select for
normal timekeeping.
• When setting the alarm time using the 12-hour format, take care to set the time
correctly as morning or afternoon (P).
4. After you set the alarm time, press B to return to the Alarm Mode.
Hour
Minutes
To switch the Daily Alarm and Hourly Time Signal on and off
Press A while in the Alarm Mode to change the status of the Daily Alarm and Hourly
Time Signal in the following sequence.
[ Alarm on indicator/Hourly Time Signal on indicator ]
Both OFF
To test the alarm
Hold down A while in the Alarm Mode to sound the alarm.
Both ON Hourly Time
Signal only
Daily Alarm
only
Time Setting Mode
To set the time and date
1. Use C to enter the Time Setting Mode.
• The seconds digits flash, because they are
selected
.
2. Press ▲ to change the selection in the following
sequence.
• While the selection is flashing, press A to switch
between 12-hour and 24-hour formats.
A
C
B
SET
P
Day of week
Month
Date
PM indicator
Hour
Minutes
Seconds
Seconds Hour Minutes
Day of Week
Date Month
3. While the seconds digits are selected (flashing), press to reset the seconds to
“00”. If you press
while the seconds count is in the range of 30 to 59, the
seconds are reset to “00” and 1 is added to the minutes. If the seconds count is in
the range of 00 to 29, the minutes count is unchanged.
4. While any other digits (besides seconds) are selected (flashing), press
to
increase the number. While the day of the week is selected, pressing
advances
to the next day. Holding down
changes the current selection at high speed.
5. After you set the time and date, press C to return to the Timekeeping Mode.
• The watch does not make any allowance for leap years. Be sure to manually set
February 29 (when one occurs) for the appropriate date.
• If you do not press any buttons for a few minutes while a selection is flashing, the
flashing stops and the watch goes back to the Timekeeping Mode automatically.