Filter
Top Products
STEP 3
LEG PRESS CABLE (243)
Eyelet end
Metal ball end
-6-
Pull out the selector pin at weight stack of K1 gym to allow top cable movable.
1. Attach the eyelet end of the Leg Press Cable (243) to the Leg Extension Arm (17),
using one 3/8" X 3" Hex Bolt (113) and one 3/8" Nylon Nut (138) as shown in Fig.1.
2. Run the cable through the slot in the front of the Seat Frame (7) and mount a
pulley in the slot using one 3/8" X 2-3/4" Hex Bolt (114), two 3/8" steel Bushing
(83), two 3/8" Washers (130) and one 3/8" Nylon Nut (138) as shown in Fig 2.
3. Slide the cable through the Base Frame (1) from front to rear slot, you will now
mount a pulley (65) in the rear slot, using 3/8" X 2-1/2" Hex Bolt (116) and one 3/8"
Nylon Nut (138). Then route the cable under a pulley mounted on the plate welded
on the rear Base Frame (1), attach Pulley Guard (28) and Metal Tab (27) at both
side of the pulley, using one 3/8" X 2" Hex Bolt (117) and one 3/8" Nylon Nut (138).
4. Route the cable up and around pulley mounted in the second hole in the bottom of
the Double Pulley Block (24), using one 3/8" X 1-3/4" Hex Bolt (118) and one 3/8"
Nylon Nut (138). When cabling is complete, this pulley can be moved upward to
take a slack or downward to gain length.
5. Continue to route the cable down to the pulley on the Base Frame (1), mount a
pulley using one 3/8" X 1-3/4" Hex Bolt (118) and one 3/8" Nylon Nut (138) as
shown in Fig.6.
6. Continue to route the cable underneath the weight stack and around the
horizontally mounted pulley on the Leg Press Main Frame (202), mount the pulley
using one 3/8" X 1-3/4" Hex Bolt (233) and one 3/8" Nylon Nut (241) as shown in
Fig. 7.
7. Continue to route the cable through the slot in the Leg Press Main Frame (202),
and under and around (exiting on the top) the lowest pulley on the Rear Leg Press
Support (208) as shown in Fig. 8,10. Mount the pulley using one 3/8" X 1-3/4" Hex
Bolt (233) and one 3/8" Nylon Nut (241).
8. Then route the cable under and around (exiting on the top) the right side (as if
sitting on seat) pulley mounted in the leg Press Main Frame (202) as shown in
Fig.9,11. Mount two pulleys here using one 3/8" X 2-3/4" Hex Bolt (232) and one
3/8" Nylon Nut (241).
9. Route the cable in the same manner under and around the uppermost pulley
mounted on the Rear Leg Press Support (208) as shown in Step 1. Mount the
pulley using one 3/8" X 1-3/4" Hex Bolt (233) and one 3/8" Nylon Nut (241).
10. Route the cable in the same manner under and around the left side (as if sitting
on seat) pulley mounted in the Leg Press Main Frame (202) as shown in Step 2.
11. Hold the ball end of the cable with Metal Washer (246) in front of the inner tube of
the receptor holder (244). Tighten the receptor Holder (244) on the Rear Leg
Press Support (208) as shown in Fig.12, using one 3/8" X 2-1/4" Hex Bolt (249),
two 3/8" Washers (238) and one 3/8" Nylon Nut (241).