Filter
Top Products
I
I
WED 14
I
I
WED 14
I
I
WED 14
W
E
D
1
4
IN
MIDDLE
OUT
CROWN
CROWN
1
4
I
I
14
START WATCH
Important: Set day and date first! Remove guard from crown and push
in. For screw-in setting crown, turn COUNTERCLOCKWISE to loosen.
Note: Crown can be located at 3 o’clock or 6 o’clock position.
SET DAY
Pull crown to “middle” position and turn CLOCKWISE until correct day
appears. If day does not change, pull crown to “out” position and turn
CLOCKWISE or COUNTERCLOCKWISE through necessary number of 24
hour periods until correct day appears.
SET DATE “FAST DATE”
3-Position Crown: Pull crown to “MIDDLE” position and turn CLOCK-
WISE or COUNTERCLOCKWISE until correct date appears.
2-Position Crown: Pull crown to “OUT” position and turn CLOCKWISE
until date changes. Repeat until correct date appears. Adjust date when
month has less than 31 days. Push crown in when finished.
SET TIME
Pull crown all the way out and turn to correct time. Push crown in to
restart. For screw-in setting crown, push crown in while turning CLOCK-
WISE to tighten.
Watches with date: Note correct time of day (A.M. or P.M.) for proper
date function.
THANK YOU FOR PURCHASING YOUR REEBOK® WATCH.
Please read instructions carefully to understand how to operate
your Reebok® watch. Your model may not have all of the
features described in this booklet.
W-113 905-095012
NOTE: Date may need to be manually
updated at the end of each month by
following above procedure (otherwise
it will continue to 39 and then roll
over to 00).
ROTATING TIME RING (OPTIONAL)
Position symbol (▲) at desired time to start or end activity.
Elapsed ring
Tide ring
COMPASS DIRECTIONAL RING (OPTIONAL)
To get approximate compass reading, point
hour hand at sun. Adjust ring so S (South) is
halfway between hour hand and 12. Adjust
every hour. Make sure hour hand is always
pointed towards the sun.
12
1
2
3
4
5
6
7
8
9
10
11
N
S
W
E
INDIGLO® NIGHT-LIGHT
Press button or crown to activate light. Patented (U.S. pat. 4,527,096 and
4,775,964) electroluminescent technology used in the INDIGLO® night-
light illuminates entire watch face at night and in low light conditions.
BRACELET ADJUSTMENT
SLIDING CLASP BRACELET
Open locking plate. Move clasp to desired bracelet
length. Exert pressure while holding locking plate
and slide clasp back and forth until it engages in
grooves on underside of bracelet. Press locking
plate down until it snaps closed. Clasp can be damaged if excessive
force is used.
FOLDOVER CLASP BRACELET
Find spring bar that connects bracelet to clasp. Using a pointed tool
(Fig. 1), push spring bar in and gently twist bracelet to disengage.
Determine wrist size, then insert spring bar in correct bottom hole
(Fig. 2). Push down on spring bar, align with top hole and release to lock
in place (Fig. 3).
Fig. 1
Fig. 2
Fig. 3
If your watch is water-resistant, meter marking or ( ) is indicated.
Water-Resistance Depth p.s.i.a.* Water Pressure Below Surface
30m/98ft 60
50m/164ft 86
100m/328ft 160
200m/656ft 284
*pounds per square inch absolute
WATER AND SHOCK RESISTANCE
WARNING: TO MAINTAIN WATER-RESISTANCE, DO NOT PRESS ANY
BUTTONS OR PULL OUT THE CROWN UNDER WATER UNLESS YOUR
WATCH IS INDICATED AS 200 METER WATER-RESISTANT.
1. Watch is water-resistant only as long as crystal, crown and case
remain intact.
2. Watch is not a diver watch and should not be used for diving.
3. Screw-in setting crown and case back must be screwed into case to
assure water-resistance (see Set Time). (Optional)
4. Rinse watch with fresh water after exposure to salt water.
5. Shock-resistance will be indicated on watch face or caseback.
Watches are designed to pass ISO test for shock-resistance. However
avoid damaging crystal/lens.
BATTERY
Reebok strongly recommends that a retailer or jeweler replace bat-
tery. If applicable, push reset button when replacing battery. Battery type
is indicated on caseback. Battery life estimates are based on certain
assumptions regarding usage; battery life may vary depending on actual
usage.
DO NOT DISPOSE OF BATTERY IN FIRE. DO NOT RECHARGE. KEEP
LOOSE BATTERIES AWAY FROM CHILDREN.
BRACELET LINK REMOVAL
Removing Links: Place bracelet upright
and insert pointed tool in opening of link.
Push pin forcefully in direction of arrow
until link is detached (pins are designed to
be difficult to remove). Repeat until desired
number of links are removed.
Reassembly: Rejoin bracelet parts. Push pin back into link in opposite
direction of arrow. Press pin down securely into bracelet until it is flush.
SOLID LINK BRACELET
Removing Links: Using a very small screw-
driver, remove screws by turning counter-
clockwise. Repeat until desired number of
links are removed. Do not remove links adja-
cent to clasp.
Reassembly: Rejoin bracelet parts and
insert screw in end of opening where it was removed. Turn screw clock-
wise until tight and flush with bracelet.