Filter
Top Products
DEFLATION AND STORAGE
1. Make sure the bed is unplugged from the electrical outlet prior to deflation.
2. To deflate your AeroBed, open the Quick Air Release Valve at the foot of the bed. Deflation takes approximately 60 seconds.
3. Roll or fold the AC cord with wand control and secure it. Fold sides of bed into the center along its length. Tightly roll your
AeroBed around the pump towards the air release end. When the bed is completely rolled, push the Quick Air Release Valve
closed until it locks.
4. Store your AeroBed in a clean, dry place at room temperature (above 50°F/10°C). Storing your AeroBed under 50°F (10°C)
and over 100°F (38°C) may affect its performance and will not be covered under warranty.
Thank you for joining the AeroBed
®
family by purchasing one of our upscale products. You can expect top-notch quality, innovation, and imagination from every AeroBed product.
You are about to enjoy the comfort of the AeroBed Raised, the finest alternative sleeping system available anywwhere. It is your responsibility to read and always follow the
safety, care, and maintenance instructions for your new AeroBed product. Always instruct and supervise others on your bed’s proper use, maintenance, and safety.
IMPORTANT: Preparation of your AeroBed product requires no tools. Use of tools may damage your bed.
7979CF Rev 07/07
Pump 103RS/DV
Instruction Manual
IMPORTANT SAFETY INFORMATION AND WARNINGS
WARNING: Adult supervision required for inflation, deflation, and maintenance. Follow all safety instructions to avoid serious injury.
WARNING: This is an electrical product – not a toy. To avoid risk of fire, burns, injury, or shock, it should not be played with or placed where small children can reach it. Do not
use in or around water.
WARNING: Product is for indoor use only.
WARNING: For household / residential use only.
- This is not a water toy. Use as a mattress only.
- This mattress is not intended for infants or persons with limited mobility. They may roll off of the mattress and become entrapped between the mattress and a wall.
- Remove all sharp objects from area where bed will be set up and used. Bed may puncture.
- Do not step or jump on bed or use as a trampoline.
- Place bed in a safe area before use, making sure that there are no sharp edges, steps, drops, or breakable items nearby. Use on flat surfaces only.
Bed may tip over on uneven surfaces.
- Do not use this bed on abrasive surfaces or near pointed/sharp items or surfaces. Protruding objects may puncture the bed.
- This bed is made of plastic and therefore may melt or burn if it comes in contact with any flame or heat source. Do not place it near or against heaters, open flame, or other hot
objects.
- Unplug product when not in use.
- Pump is not intended for continuous use. Pump may stop working or overheat if it is used for extended periods of time.
Do not use pump continuously for more than 10 minutes. To avoid excessive heat build up in the pump, let it rest for 5 minutes between complete inflation and deflation cycles.
- Do not attempt to disassemble, repair, or service the pump. No serviceable parts are contained inside. Contact Aero Products International, Inc.
at 1834 Walden Office Square, Third Floor, Schaumburg, IL 60173, for repair or servicing information.
This is the closed position. Open Air Release Valve Close Valve Using 2 Thumbs
INFLATION
If a mattress cover and/or dust ruffle is included with your AeroBed Raised, see MATTRESS COVER AND DUST RUFFLE section prior to inflation.
NOTE: BED MUST BE AT ROOM TEMPERATURE PRIOR TO INFLATING OR IT MAY CAUSE AIR LEAKS.
Remove your AeroBed from its lightweight duffle bag. Keep bag for storage.
1. Place your rolled-up bed on the floor free of obstructions or sharp objects.
2. Make certain the Quick Release Valve located at the foot of the bed is closed. Bed should be stored with valve in the closed and latched
position. If the Quick Release Valve is open, close it by using 2 thumbs to push cover and snap into valve. Be careful to avoid pushing valve
cover to the right or left as it snaps into the valve opening.
3. Remove AC plug, cord, and One Touch
®
Comfort Control Wand from plastic bag and shrink wrap.
4. Plug into any standard polarized 110 Volt AC electrical outlet. North American Electrical rating: 120 VAC 60HZ 1.0A (Note: 230VAC product
sold outside of North America). This product has a polarized attachment plug (one blade is wider than the other) as a safety feature. This plug
will fit into a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified
electrician. Never use with an extension cord unless the plug can be fully inserted. Do not attempt to defeat this safety feature.
5. Push and hold inflation/firmer button on the One Touch
®
Comfort Control Wand for approximately 3 minutes to inflate your AeroBed to the
full (firmest) capacity. Bed will not over-inflate.
6. Lie on the bed and use the Comfort Control Wand to adjust the firmness to your desired level. For firmer bed, press inflate/firmer button.
For softer bed, press deflate/softer button.
CAUTION: Do not sleep on edges of the bed. Edges are less supportive and may crush under weight.
MATTRESS COVER AND DUST RUFFLE
If a mattress cover and/or dust ruffle is included with your AeroBed Raised, please follow these use and care instructions.
1. Inflate the bed about half way. Top half of bed should be partially inflated while the bottom half is still partially deflated. Pull dust ruffle over top half of
bed into the space between the top and bottom parts of the bed around entire bed. Make sure the two long sides of dust ruffle match up with long
sides on bed.
2. Fully inflate your AeroBed Raised. Pull mattress cover over the top half of bed fitting the square opening around the pump and the straps around the
corners. Adjust ruffle and cover to your liking. Your AeroBed Raised is now ready for use.
3. After deflation, you may remove the mattress cover/dust ruffle from the bed. Or, you may store your AeroBed Raised with the mattress cover/dust
ruffle on the bed. Some wrinkling may occur.