Filter
Top Products
To use the timer in a count up
state, press the ST/STP button to
start from zero. Press the ST/STP
button to stop. Press RESET
button to reset to zero.
To set the timer to countdown,
press and hold EL/SET button for
two seconds to enter the Timer
Setting Mode . Seconds will be
set and flashing.
Press MODE button to change to
the next item, setting sequence
will be a cycle by seconds,
minutes and hours. Press ST/STP
button to adjust the flashing digits.
Once desired time has been set
press the EL/SET button to exit
the Timer Setting Mode or press
the ST/STP button to begin the
countdown timer.
CHRONOGRAPH MODE
In TIME mode, press MODE
button three times to enter the
CHRONOGRAPH mode.
To measure elapsed time, press
the ST/STP button to start the
counter. Press the ST/STP button
to stop the counter.
To view split times, press the
RESET button while the counter is
running. Press the RESET button
again to resume the counter.
To reset the chronograph, press
the RESET button when the
counter is stopped.
HOW TO OPERATE THE NIGHT
VISION™ ELECTRO-
LUMINESCENT BACKLIGHT
Press the EL/SET button to
activate the Night Vision™
electro-luminescent backlight. The
light will remain illuminated for
approximately four seconds.
CARE AND MAINTENANCE
1. Back case cover should only be
removed by an authorized watch
repair specialist.
2. Always rinse your watch in
fresh water after immersion in salt
or chlorinated water.
3. Do not expose watch or band to
chemicals such as gasoline,
aerosol sprays, paint or solvents.
4. Periodically clean with a soft
cloth and fresh water.
WARRANTY INFORMATION
Freestyle U.S.A. warrants, to the
original purchaser, that its
watches are free from defects in
materials and workmanship for a
period of ten (10) years under
normal use. The warranty
excludes batteries, crystal, watch
case plating, and strap/ bracelet/
band. The warranty excludes
normal wear and tear and abuse.
Special note: Freestyle® watches
are designed and engineered to
be highly water-resistant, and to
withstand the most active of
lifestyles. The most important
component in keeping your watch
water-resistant is the case back
O-ring, which prevents water from
entering the watch through the
case back.
Water leakage most often occurs
after improper battery
replacement. We strongly
recommend having a certified
jeweler, watch repair technician or
FreeStyle's service center replace
your battery. Water leakage due
to improper battery replacement is
not covered under warranty.
Should your Freestyle® watch
require warranty service, send it
along with the following:
1. A copy of your sales receipt
2. Your printed name and address
3. Your telephone number
4. A brief description of the
problem
5. If your watch was purchased
within the last year, there is no
charge for processing and
handling; if your watch was
purchased more than 12
months ago, please include
$8.00 for processing and
handling, using one of the
following payment methods:
-Check
-Money order
-Credit card (be sure to include
card number and expiration date)
REMEMBER: NEVER INCLUDE
A SPECIAL WATCHBAND OR
ANY OTHER PERSONAL
ARTICLES OF VALUE IN YOUR
SHIPMENT.
Send to the following address:
Freestyle
Attn: Individual Returns
5855 Olivas Park Drive
Ventura, CA 93003
(805) 477-1200 x240
Please allow 20 days for return of
your watch.
EL/SET button for two seconds to
enter into the ALARM setting
mode. First minutes will be set
and flashing.
Press MODE button to change to
the next item, setting sequence
will be a cycle by minute, hour,
month and date. Be sure that
schedule alarm is off by deleting
the month and date:
Press the ST/STP button to adjust
the flashing digits. Once
everything has been set press
EL/SET button to exit the Alarm
Setting Mode.
To set the schedule alarm, simply
follow the same steps as setting
daily alarm but set the desired
date to have the alarm sound off.
The vibration and sound alarms
will operate together for 30
seconds, and can be stopped by
pressing any key.
To turn on the alarm, press the
RESET button until the “S” symbol
shows. Alarm may also be turned
on and off under normal TIME
mode.
The sequence is as follows:
alarm on.....................
chime on....................
alarm and chime on...
alarm and chime off...
TIMER MODE
In the Normal Time Mode, press
the MODE button twice to enter
the Timer mode.
798 VIPER™
INSTRUCTIONS
FEATURES:
• CURRENT TIME
• DAY/MONTH/DATE
• CHRONOGRAPH WITH
SPLIT FUNCTION
• DUAL VIBRATION AND
SOUND ALARMS
• HOURLY CHIME
• OPTIONAL 24-HR. TIME
• WATER-RESISTANT TO
500 FT./150M
• NIGHT VISION™ ELECTRO-
LUMINESCENT
BACKLIGHTING
KEY REFERENCES
NOTE: Blue digits represent
flashing segments.
HOW TO SET TIME, DATE AND
24-HOUR FORMAT
From TIME mode: press and hold
the EL/SET button for
approximately two seconds; the
seconds digits will flash.
Pressing the ST/SP button resets
the seconds to zero. Press MODE
button to change to the next item.
The setting sequence will be a
cycle by seconds, hours, month,
date and day of week. Pressing
the ST/SP button to adjust the
flashing digits. After the time and
date have been set, press the
EL/SET button to return to normal
TIME mode.
To view the time in 24-hour format,
simply press the ST/ STP button.
HOW TO SET THE ALARM
In TIME mode, press the MODE
button once to enter the ALARM
mode. The alarm can be set to
either schedule or daily alarm
EL/SET ST/STP
MODE RESET