Coleman 2000002250 Tent User Manual


 
STITCH LINE
To Set Up Tent
1. Unfold tent and spread out on a clean, level surface with the
door facing the desired direction. (Fig. 1)
2. Assemble all fiberglass and metal poles by interlocking the
shock-corded, sections together.
3. Insert thick, black, Top Poles through the sleeves on top of
tent forming an X”; then push end of each pole into black Pole
Connector to form an arch. (Fig. 1 & 1A)
4. Insert thick, grey Top Pole through the grey trimmed center
sleeve, running from the front to the back of tent; then push
end of pole into black Pole Connector to form an arch.
(Fig. 1 & 1B)
5. Insert four metal Leg Poles into end of Pole Connectors at the
four corners of the tent. (Fig. 1 & 1C)
NOTE: Make sure end with metal “V” spring is inserted into
Pole Connector.
6. Insert two metal Leg Poles (with white markings) into end
of Pole Connectors at front & back of the tent. (Fig. 1 & 1C)
NOTE: Make sure end with metal “C” spring is inserted into
Pole Connector.
Fig. 1
Door & Front of Tent
7. Rotate metal Leg Poles to upright position; then insert metal
pin on web strap at front, back, & four corners of tent into
bottom of each pole. (Fig. 2 & 2A)
NOTE: You can use the tri-glide to adjust the length of the
center webbing to make it easier to insert the metal pin into
the metal center pole.
8. Snap large frame clips on seams of tent onto metal Leg Poles
to secure. (Fig. 2 & 2B)
9. Stretch four corners of tent until taut; then drive metal stake
through ring on web strap of each to secure (Fig. 2 & 2C).
10. Stretch web strap at front & back of tent until taut; then drive
metal stake through ring on each to secure (Fig. 2 & 2C).
Before you begin
Read all instructions before set up.
• Select a level site clear of rocks, branches, and other hard or sharp
objects, to install your tent.
WARNING: Keep clear of overhead power lines
.
• Do not set up your tent under trees because of potential lightning strikes
or falling tree limbs in inclement weather.
• Secure with all
stakes and guylines provided to prevent property damage
or personal injury.
• For best results in windy conditions, position narrow end of tent into
the wind.
• Enlist the help of at least one other person to assist you when it is time
to assemble the tent.
Metal Leg Pole
Hinged, Rigid Door
1. Insert Vertical Door Pole (shorter black
pole with plastic cap tips) through zippered
vertical sleeve on hinged side of door.
(Fig. 3)
2. Insert end of Vertical Door Pole into bottom
hinge plate, apply pressure to form a slight
bow, then insert other tip of pole into top
hinge (Fig. 4). Zip up vertical pole sleeve.
3. Insert Door Pole (long, black pole with
plastic cap tips) into zippered pole sleeve
at top of door. (Fig. 5)
4. Insert end of Door Pole into top hinge
plate, apply pressure to form a bow, then
insert other tip of pole into the bottom
hinge. (Fig. 6)
5. Zip up “C” shaped pole sleeve to
enclose Door Pole. (Fig. 7)
Fig. 5
Fig. 7
Fig. 3
Fig. 4
Fig. 6
Pole
Sleeve
Pole Sleeve
2A
To Attach Rainfly
1. Drape Rainfly over tent with the triangle-shaped leg flaps with
elastic cords centered over the four corner of the tent. (See
Fig. 8 on other side of this tag).
NOTE: Hook and loop fasteners, located on seams of under
side of rainfly, should be centered over the Leg Poles.
(continued on other side)
Pole Descriptions
Pole Pole Pole
Description Qty. Dia. Repair Kit Replacement Kit
Leg Pole, metal 4 19mm N/A 5010000650
Leg Pole, metal,
with white marking 2 19mm N/A 5010000651
Top Pole, thick, grey, 1 12.7mm 5010000538 5010000550
Top Pole, thick, black 2 12.7mm 5010000538 5010000550
Door Pole, long, thin, black,
fiberglass, rubber tips 1 6.3mm 5010000543 5010000545
Vert. Door Pole, short, black,
fiberglass, rubber tips 1 6.3mm 5010000543 5010000545
Metal Leg Pole with
White Marking
Pole
Connector
2B
CABIN TENT 13’ X 9’ MODEL 2000002250
Metal Leg Pole with
White Marking
Metal Leg Poles
Pole
Connector
Metal Leg Pole
1C
Fig. 2
“C” Spring
“C” Spring
2C
1A
1B
Tri-Glide