Coleman 2000001597 Tent User Manual

6. Rotate all eight Leg Poles upright and insert
pin on each web loop at the side locations
as shown. (Fig. 7 & 7A)
(continued on other side)
Fig. 6
Fig. 7
7. Locate the plastic hooks at sides and
corners of tent, then snap onto Leg
Poles to attach. (Fig. 8)
9. Insert plastic stakes through web
straps located on both sides of tent,
then drive in to secure. (Fig. 10)
NOTE: It may be necessary to remove
metal stakes through web straps at
side of tent and screen room, pull tent
taut, and drive in stakes to secure.
Fig. 10
8. To stretch tent to finished size:
Push in button on Leg Pole while
twisting lower Leg Pole section
counterclockwise (Fig.9);
Pull up on top Leg Pole section
until tent is taut;
Twist the lower Leg Pole clock-
wise until the button locks into
the center or lowest hole;
Repeat on remaining Leg Poles.
Fig. 8
Fig. 9
Center Hole
Lower Hole
Leg Pole
Leg Pole
MODEL 2000001597
Curved Ridge
Poles with Red
Marking in
center 2
Hinged, Rigid Door
1. Assemble Vertical Door Pole (shorter black pole with plastic
cap tips); then insert through zippered vertical pole sleeveon
hinged side of door. (Fig. 11)
2. Insert end of Vertical Door Pole into bottom hinge plate,
apply pressure to form a slight bow, then insert other tip of
pole into top hinge. Zip up vertical pole sleeve. (Fig. 12 & 13)
3. Assemble Door Pole (longer black pole with plastic cap tips);
then insert into zippered pole sleeve at top of door. (Fig. 14)
4. Insert end of Door Pole into top hinge plate, apply pressure
to form a bow, then insert other tip of pole into the bottom
hinge. (Fig. 15)
5. Zip up pole sleeve to enclose Door Pole. (Fig. 16)
Fig. 1
To Set Up Tent
1. Unfold tent and spread out on a clean, level surface with the
door facing the desired direction. Unzip doors. (Fig. 1)
4. Assemble eight, steel, shock-corded, Leg Poles. Push down
on steel button on tapered end and insert into end with
four holes.
NOTE: Make sure steel button locks
into third hole on pole as shown. (Fig.4)
5. Insert curved end of Leg Poles
(with red marking) into the ends of the
Ridge Poles (with red
marking). Insert curved
end of remaining short
Leg Poles into the ends
of the remaining Ridge
Poles. (Fig. 5 & 6)
Ridge Pole with
Red Marking
Button in third hole
Fig. 4
Fig. 5
Fig. 2
with Red
Curved End of
Long Leg Pole
2. Pull four corners of tent taut, then secure by
driving stakes through web loops at an angle
for better anchoring. (Fig. 2)
Ridge Pole
with Red
Fig. 3
with Red
3. Assemble four, steel, shock-corded,
curved Ridge Poles. Insert Ridge Poles
(with red marking) into center sleeves
on top of tent with the red trim (Fig. 3).
Insert the remaining curved Ridge Poles
into the other two sleeves on top of tent.
Pole Descriptions
Pole Pole Pole
Description Qty. Dia. Repair Kit Replacement Kit
Long Leg Pole, steel
(w/ red marking) 4 19mm N/A 5010000608
Short Leg Pole, steel 4 19mm N/A 5010000610
Curved Ridge Pole, steel
(w/ red marking) 2 19mm N/A 5010000607
Curved Ridge Pole, steel 2 19mm N/A 5010000609
Awning Pole, black,
fiberglass, metal tips 1 6.3mm 5010000543 5010000545
Door Pole, long, thin, black,
fiberglass, rubber tips 1 6.3mm 5010000543 5010000545
Vert. Door Pole, short, black,
fiberglass, rubber tips 1 6.3mm 5010000543 5010000545
Fig. 11 Fig. 12 Fig. 13
Fig. 14
Fig. 15
Fig. 16
Vertical Pole
Door Hinge
Before you begin
Read all instructions before set up.
• Select a level site clear of rocks, branches, and other hard or sharp
objects, to install your tent.
WARNING: Keep clear of overhead power lines
• Do not set up your tent under trees because of potential lightning strikes
or falling tree limbs in inclement weather.
• Secure with all
stakes and guylines provided to prevent property damage
or personal injury.
• For best results in windy conditions, position narrow end of tent into
the wind.
• Enlist the help of at least one other person to assist you when it is time
to assemble the tent.