Filter
Top Products
Operation Guide 5196/5252/5301
E-9
x
x
x
x
Go to step 2.
The watch is charged. For details about charging, see “Charging the Watch”
(page E-14).
NEXT
Battery is starting to go low.
Battery is low.
E-8
Things to check before using the watch
1. Observe the movement of the
x
Second Hand.
Is the
x
Second Hand moving smoothly at one-second intervals?
Charge the watch by placing it in a location where it is exposed to light. For
details, see “Charging the Watch” (page E-14).
1 second 1 second 2 seconds
x
x Second Hand moving in the
following pattern.
Is the
x
Second Hand moving at two-second intervals or is it stopped completely?
NO
NO
YES
YES
YES
E-7
High-speed Cancel
Rotate the crown in the reverse direction of the
movement or press the A button.
Note
Leaving the crown pulled out for more than two minutes without performing any x
operation will automatically cause the setting operation to become disabled. If this
happens, press the crown back in and then pull it out again to confi gure settings.
High-speed movement can be used when setting the current time (page E-36) and
x
when performing home position adjustment (page E-44).
E-6
Second click
For confi guring time, date and other settings
Note
When you push the crown back in from the fi rst click, the x
x
Second Hand will perform
movement that indicates whether the watch’s battery requires charging before
resuming regular timekeeping. See “Charging Guide” (page E-17).
High-speed Forward and Reverse Movement
While the crown is pulled out, rotating it more than one
full turn either way will cause the hands or Day indicator
to start to move at high speed. High-speed movement
will continue even if you release the crown.
E-5
Crown Operations
The crown can be pulled out to one of two (click) positions. Never apply undue force
when pulling out the crown.
Important!
When pulling out the crown, avoid using undue force, which creates the risk of
x
personal injury to your fi ngers and fi ngernails, and of watch malfunction.
First click
For selecting the location setting
E-4
About the face
The following explains the meanings of the markings on the
watch’s face.
Y (YES)/N (NO): Time calibration signal reception result1.
Y (YES): Successful
N (NO): Unsuccessful
See “To check the result of the latest receive operation”
x
(page E-30).
RC: Receive in progress2.
See “To perform manual receive” (page E-29).
x
A (AM)/P (PM): AM and PM indications when setting 3.
the time
See “To set the time manually” (page E-36).
x
CN (HKG, HONG KONG)/OFF/JP (TYO, TOKYO): 4.
Signal reception location
See “Radio Controlled Atomic Timekeeping” (page E-23). x
'
)
(&
E-3
Hand Functions
z
Hour Hand
x
Second Hand
c
Minute Hand
v
Day Indicator
This User’s Guide uses numbers shown above to identify watch hands and indicators.
The operational procedures for Modules 5196, 5252 and 5301 are identical. All of
x
the illustrations in this manual show Module 5196.
The module number is engraved on the back cover of the watch case. *
Important!
The
x A button is designed to protect against accidental pressing.
Use a thin pointed object to press the depression of the button to
operate it.
In the illustrations in this manual, the
x A button is emphasized for
ease of understanding.
E-2
About this manual
Operations are performed using the watch’s crown and the A button.
Module 5196
+@B
>
Module 5252
+@B
>
Module 5301
+@B
>
E-1
ENGLISH
Congratulations upon your selection of this CASIO watch.
Note that the product illustrations in this manual are intended for reference only, and so
x
the actual product may appear somewhat different than depicted by an illustration.
Note that CASIO COMPUTER CO., LTD. assumes no responsibility for any
damage or loss suffered by you or any third party arising through the use of this
product or its malfunction.
MA1208-EA
Ú
#!3)/#/-054%2#/,4$