Filter
Top Products
1
Operation Guide 5168/5236
MA1104-EA
Your watch may differ somewhat from the one shown in the illustration. •
Day
Crown
(Normal position)
First click
(Setting day)
Second click
(Setting time)
Second hand
Minute hand
Hour hand
24-hour hand
[5168]
Day
Crown
(Normal position)
First click
(Setting day)
Second click
(Setting time)
Second hand
Minute hand
Hour hand
24-hour hand
[5236]
To set the time
Pull the crown out to the second click.1.
At this time, the second hand will move to • 0 (reset position) and stop there.
Set the hands by rotating the crown. Rotate the crown to move the hands 2.
clockwise. Move the minute hand four or five minutes past the time you want to
set, and then back it up to the proper setting.
Carefully set the time, making sure to distinguish between AM and PM. •
Push the crown back in to the normal position to restart timekeeping.3.
To set the day
Pull the crown out to the first click.1.
Set the day by rotating the crown.2.
Push the crown back in to the normal position.3.
Avoid changing the date setting while the current time is between 9:00 p.m. and •
1:00 a.m.
Using the Stopwatch
Stopwatch hour hand
(10 hours)
Stopwatch second hand
(37 seconds)
Stopwatch minute hand
(2 minutes)
Stopwatch 1/20 second hand
(.8 second)
This hand moves right and left •
to indicate the 1/20 second
count during the first
60 seconds.
[5168]
Stopwatch hour hand
(10 hours)
Stopwatch second hand
(37 seconds)
Stopwatch minute hand
(2 minutes)
Stopwatch 1/20 second hand
(.8 second)
This hand moves right and left •
to indicate the 1/20 second
count during the first
60 seconds.
[5236]
The stopwatch lets you measure elapsed time up to 11 hours, 59 minutes,
59.95 seconds.
To measure elapsed time
Press 1. B to enter the Stopwatch Mode.
The stopwatch 1/20 second hand will move to the 0 position. •
Press 2. A to start the stopwatch.
Press 3. A to stop the stopwatch.
You can resume the measurement operation by pressing • A again.
Check the elapsed time.4.
The example above shows an elapsed time of 10 hours, 2 minutes, •
37.80 seconds.
Press • B to reset the stopwatch.
To return the function of the stopwatch 1/20 second hand to the timekeeping
second hand (indicating the current seconds count), press B again. This will
enter the Timekeeping Mode.
Notes:
Do not try to perform stopwatch operations while the crown is pulled out either •
to the first or second click. If you try to press a button, you might accidentally
cause the crown to rotate and change the current time or day setting.
If the starting positions of the stopwatch second hand and 1/20 second hand •
become misaligned, use the following procedures to adjust the position of the
stopwatch second hand so it points to 12 o’clock and the 1/20 second hand so
it points to .0 when the stopwatch is reset.
To adjust the positions of the stopwatch hands
Press 1. B to reset the stopwatch, and check the alignment of the stopwatch
second hand (12 o’clock) and 1/20 second hand (12 o’clock).
Pull out the crown to the second click.2.
Press 3. A to move the stopwatch second hand.
If the stopwatch 1/20 second hand is aligned correctly, proceed to step 5. If 4.
the stopwatch 1/20 second hand is also misaligned, press B to move the
stopwatch 1/20 second hand.
After making the adjustments you want, push the crown back in to its normal 5.
position.
Note that pulling the crown out also stops the timekeeping second hand. After •
performing the above procedure, you should also adjust the timekeeping setting.
For a watch with an elapsed time bezel ■
Rotate the elapsed time bezel to align the
mark with the
minute hand.
After certain amount of time elapsed, read the graduation on
the elapsed time bezel which the minute hand points to.
The elapsed time is indicated.
Elapsed time bezel
Some water resistant models are equipped with a screw •
lock crown.
With such models, you must unscrew the crown in the •
direction noted in the illustration to loosen it before you can
pull it out. Do not pull too forcibly on such crowns.
Also note that such watches are not water resistant while •
their crowns are loosened. Be sure to screw the crowns
back in as far as they will go after making any setting.
Specifications
Accuracy at normal temperature: ± 20 seconds a month
Display: 3 analog hands (timekeeping hour and minutes, stopwatch seconds),
4 dials (timekeeping 24-hour, timekeeping seconds/stopwatch 1/20 second,
stopwatch hours, stopwatch minutes), day
Stopwatch function: Measuring capacity: 11:59'59.95"
Measuring unit: 1/20 second
Measuring mode: Elapsed time
Battery: One silver oxide battery (Type: SR927W)
Approximately 2 years on type SR927W