Filter
Top Products
1
Operation Guide 5203 5204
MA1010-EA
Your watch may differ somewhat from the one shown in the illustration. •
Minute hand
Hour hand
24-hour disk
Second hand
Day
Crown
(Normal position)
First click
(Setting Day)
Second click
(Setting Time)
To set the time
Pull the crown out to the 1.
second click.
At this time, the second •
hand will move to the
12 o’clock position and
stop there.
Set the hands by rotating the 2.
crown. Rotate the crown to
move the hands clockwise.
Move the minute hand four or
five minutes past the time you
want to set, and then back it
up to the proper setting.
Make sure that you also •
set the 24-hour disk to the
correct hour of the day.
Push the crown back in to 3.
the normal position to restart
timekeeping.
To set the day
Pull the crown out to the first click.1.
Set the day by rotating the crown towards you.2.
Push the crown back in to the normal position.3.
Avoid changing the date setting while the current time is between 9:00 p.m. and •
1:00 a.m.
Using the Stopwatch
Stopwatch minute hand
This hand rotates and *
indicates the second
count during the first
60 seconds.
Stopwatch
1/100 second hand
Stopwatch second
hand
The stopwatch lets you measure elapsed time up to 59 minutes, 59.99 seconds.
To measure elapsed time (First 60 seconds)
Press 1. A to start the stopwatch.
Press 2. A to stop the stopwatch.
You can resume the measurement operation by pressing • A again.
Check the elapsed time.3.
The example below shows an elapsed time of 40.30 seconds. •
Stopwatch 1/100 second hand
[30]
Stopwatch second hand
[40 seconds]
Press • B to reset the stopwatch.
This will enter the Timekeeping Mode.
To measure elapsed time (After the first 60 seconds)
Press 1. A to start the stopwatch.
During elapsed time measurement, the stopwatch 1/100 second hand •
automatically rotates for the final second of each minute.
Press 2. A to stop the stopwatch.
You can resume the measurement operation by pressing • A again.
Press 3. A and the stopwatch 1/100 second hand will move to the
1/100 second count.
If the elapsed time operation was stopped during the final second of each •
minute, the stopwatch 1/100 second hand will already be pointing at the
1/100 second count. Do not press A at this time, because doing so will
restart the elapsed time operation.
Check the elapsed time.4.
The example below shows an elapsed time of two minutes, 40.30 seconds. •
Stopwatch 1/100 second hand
[30]
Stopwatch second hand
[40 seconds]
Stopwatch minute hand
[2 minutes]
Press • B to reset the stopwatch.
This will enter the Timekeeping Mode.
Notes:
Do not try to perform stopwatch operations while the crown is pulled out either •
to the first or second click. If you try to press a button, you might accidentally
cause the crown to rotate and change the current time or day setting.
If the starting positions of the stopwatch second hand and 1/100 second hand •
become misaligned, use the following procedures to adjust the positions of the
hands so they point to 12 o’clock when the stopwatch is reset.
To adjust the positions of the stopwatch hands
Press 1. B to reset the stopwatch, and check the alignment of the stopwatch
second hand and 1/100 second hand.
Pull out the crown to the second click.2.
Press 3. A to move the stopwatch 1/100 second hand.
If the stopwatch minute hand is aligned correctly, proceed to step 5. If the 4.
stopwatch minute hand is also misaligned, press B to move the stopwatch
second hand.
After making the adjustments you want, push the crown back in to its normal 5.
position.
Note that pulling the crown out also stops the timekeeping second hand. After •
performing the above procedure, you should also adjust the timekeeping setting.
For a watch with an elapsed time bezel ■
Rotate the elapsed time bezel to align the
mark with the
minute hand.
After certain amount of time elapsed, read the graduation on
the elapsed time bezel which the minute hand points to.
The elapsed time is indicated.
Elapsed time bezel
Some water resistant models are equipped with a screw •
lock crown.
With such models, you must unscrew the crown in the •
direction noted in the illustration to loosen it before you can
pull it out. Do not pull too forcibly on such crowns.
Also note that such watches are not water resistant while •
their crowns are loosened. Be sure to screw the crowns
back in as far as they will go after making any setting.
Specifications
Accuracy at normal temperature: ± 20 seconds a month
Display: 3 analog hands (timekeeping hour and minutes, stopwatch 1/100 seconds),
3 dials (timekeeping 24-hour and seconds, stopwatch minutes), day
Stopwatch function: Measuring capacity: 59'59.99"/Measuring unit: 1/100 second
Measuring modes: Elapsed time
Battery: One silver oxide battery (Type: SR927W)
Approximately 2 years on type SR927W (assuming one stopwatch operation 60 min./
day)