Filter
Top Products
1
Operation Guide 2962/2992
MA0506-EA
About This Manual
• The operational procedures for Modules 2962 and 2992
are identical. All of the illustrations in this manual show
Module 2962.
• Button operations are indicated using the letters shown
in the illustration.
• Each section of this manual provides you with the
information you need to perform operations in each
mode.
Module 2962
Module 2992
Timekeeping Mode Alarm Mode Stopwatch Mode Time Setting Mode
Press .
General Guide
• Press B to change from mode to mode.
• In any mode, press A to illuminate the display.
• After you perform an operation in any mode, pressing B returns to the Timekeeping
Mode.
PM indicator
Day of week
Day
Hour : Minutes Seconds
Timekeeping
Use the Timekeeping Mode to view the current time and
date.
• Day of the week is displayed as follows.
SU: Sunday MO: Monday
TU: Tuesday WE: Wednesday
TH: Thursday FR : Friday
SA: Saturday
To toggle between 12-hour and 24-hour timekeeping
In the Timekeeping Mode, press C to switch between the
12-hour and 24-hour formats.
• With the 12-hour format, the PM indicator (P) appears
for times in the range of noon to 11:59 p.m. and no
indicator appears for times in the range of midnight to
11:59 a.m.
• With the 24-hour format, times are displayed in the
range of 0:00 to 23:59, with 24H indicator.
Backlight Precautions
The backlight uses an EL (electro-luminescent) panel that causes the entire display to
glow for easy reading in the dark. In any mode, press A to illuminate the display.
• The electro-luminescent panel that provides illumination loses power after very long
use.
• The illumination provided by the backlight may be hard to see when viewed under
direct sunlight.
• The watch may emit an audible sound whenever the display is illuminated. This is
due to vibration of the EL panel used for illumination, and does not indicate
malfunction.
• Frequent use of the backlight shortens the battery life.
Hourly time
signal on indicator
Mode indicator
Alarm time
(Hour : Minutes)
Alarm on indicator
2. Press A to change the selection in the following sequence.
• Pressing A also illuminates the display.
Hour
Normal Alarm Mode (No digit flashes)
Minutes
3. Press C to increase the selected digits. Holding down C changes the number at
high speed.
• The format (12-hour and 24-hour) of the alarm time matches the format you select
for normal timekeeping.
• When setting the alarm time using the 12-hour format, take care to set the time
correctly as morning or afternoon (P).
4. After you set the alarm time, press A to return to the Alarm Mode.
• If you do not operate any button for a few minutes while a selection is flashing, the
flashing stops and the watch goes back to the Timekeeping Mode automatically.
Alarm
When the Daily Alarm is turned on, the alarm sounds for
20 seconds at the preset time each day. When the Hourly
Time Signal is turned on, the watch beeps every hour on
the hour.
• All of the operations in this section are performed in the
Alarm Mode, which you enter by pressing B.
To set the alarm time
1.Hold down A while in the Alarm Mode until the hour
digits start to flash on the display. The hour digits flash
because they are selected.
• This operation automatically turns on the alarm.
Mode indicator
Minutes Seconds
1/100 second
To stop the alarm
Press A to stop the alarm after it starts to sound.
To switch the Daily Alarm and Hourly Time Signal on and off
Press C while in the Alarm Mode to change the status of the Daily Alarm and Hourly
Time Signal in the following sequence.
Hourly Time
Signal only
Daily Alarm
only
Both offBoth on
To test the alarm
Hold down C while in the Alarm Mode to sound the alarm.
Stopwatch
The Stopwatch Mode lets you measure elapsed time, split
times, and two finishes. The range of the stopwatch is
59 minutes, 59.99 seconds.
• The stopwatch continues to run, restarting from zero
after it reaches its limit, until you stop it.
• The stopwatch measurement operation continues even
if you exit the Stopwatch Mode.
• Exiting the Stopwatch Mode while a split time is frozen
on the display clears the split time and returns to
elapsed time measurement.
• All of the operations in this section are performed in the
Stopwatch Mode, which you enter by pressing B.
To measure times with the stopwatch
(a) Elapsed time measurement
Start
Stop Re-start Stop Clear
Start
Split release Stop Clear
Start
Split Stop Split release Clear
(b) Split time measurement
(c) Split time and 1st-2nd place times
First runner
finishes.
Display time of
first runner.
Second runner
finishes.
Display time of
second runner.
Split
(SPL displayed)
• Pressing A also illuminates the display.