Filter
Top Products
USER’S GUIDE 2707
1
General Guide
• Press C to change from mode to mode.
• In any mode, press L to illuminate the display.
Data Memory Mode
Stopwatch Mode
Timekeeping Mode
Alarm Mode
▲
▲
▲
Hand Setting Mode
▲
▲
Press C.
▲
World Time Mode
Timekeeping
Use the Timekeeping Mode to set and view the current time and date.
• In the Timekeeping Mode, press D to change the screen format as shown below.
Press D.
▲
▲
Date and Time
Analog
Seconds
Date
Seconds and Date
▲
Seconds
Hour : Minutes
Month – Day
Day of week
PM
indicator
▲
▲
• Pressing A displays the Last Signal screen (date and time the time calibration
signal was last received) in the Timekeeping Mode.
Current Time Setting
This watch automatically adjusts its time setting in accordance with a time calibration
signal. You can also perform a manual procedure to set the time and date, when
necessary.
• Before using the watch in Western Europe, first use the procedure under “Setting Up
the Watch for Use in Western Europe” to set the time in accordance with a time
calibration signal.
• Note that after you set your Home City (the city where you normally use the watch)
code, you must also turn on the watch’s time calibration signal receiver if you want to
enable auto time calibration. See “About Auto Receive” for more information.
• See “Setting the Digital Time and Date Manually” for information about manual
settings.
• The analog time of this watch is synchronized with the digital time. Because of this,
the analog time setting is automatically adjusted whenever you change the digital
setting. See “Analog Timekeeping” for more information.
Last Signal Screen
▲
Press A.
Receive date
Receive time
▲
Setting Up the Watch for Use in Western Europe
You need to make the following three settings before using this watch in Western
Europe. The following provides a general overview of the setting procedure. For full
details, see “Setting the Time and Date Manually” and “Time Calibration Signal
Reception”.
• Specify the city code for your Home City (the city where you will normally use the
watch).
• Select the auto summer time (DST) setting.
• Perform the manual time calibration signal receive operation to set the current time.
To set up the watch for use in Western Europe
1. In the Timekeeping Mode, press B. This causes the
current auto receive on/off setting (the receive indicator)
to flash, which indicates the setting screen.
2. Press C to move the flashing to the city code setting.
3. Use D(+) and A(–) to select the city code you want to
use as your Home City.
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
City code
GMT differential
Receive indicator
• The following are the city codes for major cities in the
Western Europe time zones.
BER and PAR: Berlin, Paris, Milan, Rome,
Amsterdam, Hamburg, Frankfurt,
Vienna
LON: London
4. Press C to display the summer time (DST) setting
screen.
5. Use D to select AUTO DST.
• AUTO DST specifies auto switching between Daylight
Saving Time and Standard Time.
6. Press B to exit the setting screen.
• If you changed the digital time setting with the above
steps, the analog hands move at this time to match it.
Wait until the analog hands stop moving before you
advance to the next step.
7. Hold down A for about two seconds until the watch
beeps.
l
l
l
l
l
l
l
l
l
l
l
l
Receive indicator
• Release A and the message receiving appears to indicate that signal reception
has started.
• Time calibration signal reception takes from two to six minutes. Take care that you
do not move the watch during this time.
• If the watch is indoors, we recommend that you place the watch near a window to
allow better signal reception.
• After signal reception is complete, the display of the watch changes to the Last
Signal screen, and the analog time of the watch is adjusted automatically.
Time Calibration Signal Reception
This watch is designed to pick up a time calibration signal and update its time setting
in accordance with the signal. There are two different methods you can use to receive
the signal: Auto Receive and Manual Receive. With Auto Receive, the watch
automatically receives the calibration signal three times each day and makes
appropriate adjustments. With Manual Receive, you perform a specific button
operation to receive the calibration signal.
Before performing a signal receive operation, remove the watch from you wrist and
position it as shown in the illustrations below.
• If your watch has a resin band, pass the end of the band through the band loop and
place the watch on a stable surface.
Resin band Metal band
Pass through band loop.
Note
• If you are using the time calibration signal to set the time for this watch, be sure to
correctly set your Home City. Otherwise, there is the chance that the watch will not
set the correct time.
• Note that signal reception is possible only when the watch is within range of a time
calibration signal transmitter, and BER, PAR, LON, or ATH is selected as the Home
City code.
• See “City Code Table” for a complete list of available city codes.
• The current time setting in accordance with the time calibration signal takes priority
over any time settings you make.
• Auto receive is turned on when the watch is shipped from the factory.
• Time calibration signal reception is disabled while the analog hands are moving after
you change the digital time setting.
• See the information under “Time Calibration Signal Reception” if you experience
problems with time calibration signal reception.
To perform manual time calibration signal reception
1. Place the watch on a stable surface so its top (12 o'clock side) is facing in the
general direction of the signal transmitter.
• Note that signal reception is poor if the watch is on its back or side.
2.In the Timekeeping Mode, hold down A for about two
seconds until the watch beeps.
• Release A and the message receiving appears to
indicate that signal reception has started.
• Time calibration signal reception takes from two to six
minutes. Take care that you do not move the watch
during this time.
• After signal reception is complete, the display of the
watch changes to the Last Signal screen, and the
analog time of the watch is adjusted automatically.
• The receive indicator indicates that the calibration time
reception attempt was successful.
Receive indicator
Note
• To interrupt a receive operation and return to the Timekeeping Mode, press A.
• If the receive operation is unsuccessful, the message ERROR! appears on the
display for about one or two minutes. After that, the watch returns to the
Timekeeping Mode.
• You can also change from the Last Signal or ERROR! screen to the normal
timekeeping screen by pressing A.
About the Receive Indicator
The receive indicator shows the strength of the calibration signal being received. For best
reception, be sure to keep the watch in a location where signal strength is strongest.
Weak
Strong
• Even in an area where signal strength is strong, it takes about 10 seconds for signal
reception to stabilize enough for the receive indicator to indicate signal strength.
• Use the receive indicator as a guide for checking signal strength and for finding the
best location for the watch during signal receive operations.
• The receive indicator remains on the display in all modes following reception of the
time calibration signal and calibration of the watch’s time setting. The receive
indicator does not appear if signal reception was unsuccessful or after manual
adjustment of the current time setting.