Casio 1813 Watch User Manual


 
1632/1813-2
Moving the watch to a position that is parallel to the ground and then tilting
it towards you more than 40 degrees causes the backlight to illuminate.
The backlight may not illuminate if the face of the watch is more than 15
degrees off parallel as shown below. Make sure that the back of your hand
is parallel to the ground.
Static electricity or magnetic force can interfere with proper operation of the
Auto Light Switch function. If the backlight does not illuminate, try moving
the watch back to the starting position (parallel with the ground) and then tilt
it back toward you again. If this does not work, drop your arm all the way
down so it hangs at your side, and then bring it back up again.
Under certain conditions the backlight may not light until about one second
or less after turn the face of the watch towards you. This does not necessarily
indicate malfunction of the backlight.
Warning!
Never try to read your watch when mountain climbing or hiking in
areas that are dark or in areas with poor footing. Doing so is dangerous
and can result in serious personal injury.
Never try to read your watch when running on a roadside or in any
other location where there might be vehicular or pedestrian traffic.
Doing so is dangerous and can result in serious personal injury.
Never try to read your watch when riding on a bicycle or when
operating a motorcycle or any other motor vehicle. Doing so is
dangerous and can result in a traffic accident and serious personal
injury.
When you are wearing the watch, make sure that its Auto Light Switch
function is turned off before riding on a bicycle or operating a
motorcycle or any other motor vehicle. Sudden and unintended
operation of the Auto Light Switch function can create a distraction,
which can result in a traffic accident and serious personal injury.
More than 15 degrees
too high
More than 15 degrees
too low
Parallel to ground
TIMETEL
SCHVIT ALM
STW
B
M
A
C
Text area
Number area
[New Data Display]
Cursor
TIMETEL
SCHVIT ALM
STW
TIMETEL
SCHVIT ALM
STW
B
M
A
C
TELEMEMO MODE
The Telememo Mode lets you store up to 100*
pairs of name and telephone number data.
Stored data is sorted automatically into
alphabetic sequence based on the text area
text.
*
The Telememo Mode shares memory with
the Schedule-memo Mode. This means that
the maximum number of Telememo Mode
entries you can store is reduced by one each
time you store a Schedule-memo Mode data
item.
Whenever you enter the Telememo Mode,
the text
TELEPHONE scrolls across the
text area of the display once. Next, Telememo
data appears on the display. You can interrupt
scrolling of the initial text and immediately
display Telememo data at any time by pressing
A, B, or C.
See the “CHARACTER LIST” at the back of this manual for details on how
the watch sorts data.
The data item that appears on the display when you enter the Telememo
Mode is the same one that was displayed the last time you exited the
Telememo Mode.
To input new Telememo data
1. In the Telememo Mode, press B and C at the
same time to display the new data display.
If there is no Telememo data stored in memory
yet, the new data display appears as soon as
you enter the Telememo Mode.
If the message
FULL appears in the text area
of the display, it means that memory is full. To
store more data, you will first have to delete
some of the data stored in memory.
Remaining
memory
Mode indicator
Text area
TIMETEL
SCHVIT ALM
STW
TIMETEL
SCHVIT ALM
STW
P
B
M
A
C
Text area
Text
Hour : Minutes
Mode indicator
Remaining
memory
Text area
Parallel to
ground
More
than
40°
2. Hold down A until the flashing cursor appears in the text area of the
display.
3. Input a name in the text area and a telephone number in the number area.
You can input up to eight characters in the text area, and 12 digits in the
number area.
You can input only hyphens, numbers and spaces in the number area (you
cannot input text).
Use B and C to input characters, and M to move the cursor around the
display. For details, see “INPUTTING TEXT”.
4. After inputting your data, press A to store it and return to the Telememo
Mode.
When you press A to store data, the message
SORT appears on the
display for a few seconds. After the sort operation is complete, the normal
Telememo Mode display (without the cursor) appears.
To recall Telememo data
In the Telememo Mode, press C to scroll forward through stored data items
or B to scroll in reverse.
Holding down either button scrolls through the data at high speed.
The new data display appears whenever scrolling reaches the beginning or
the end of data currently stored in memory.
To edit Telememo data items
1. In the Telememo Mode, scroll through the data items and display the one
you want to edit.
2. Hold down A until the flashing cursor appears in the text area of the
display.
3. Use M to move the cursor to the character you want to change.
4. Change the character.
See “INPUTTING TEXT” for details.
5. After making the changes that you want, press A to store them and return
to the Telememo Mode.
To delete Telememo data
1. In the Telememo Mode, scroll through the data items and display the one
you want to delete.
2. Hold down A until the flashing cursor appears in the text area of the
display.
3. Press B and C at the same time to delete the Telememo data item.
At this time the cursor appears in the text area, ready for input.
4. Press A to return to the Telememo Mode.
SCHEDULE-MEMO MODE
Schedule-memo Mode lets you store up to 100*
Schedule-memo data items (appointment date
and time, and text). Whenever a time you set is
reached, an alarm sounds and the text you
input for the data scrolls across the text area of
the display.
*
The Schedule-memo Mode shares memory
with the Telememo Mode. This means that
the maximum number of Schedule-memo
Mode entries you can store is reduced by one
each time you store a Telememo Mode data
item.
Whenever you enter the Schedule-memo
Mode, the text
SCHEDULE scrolls across
the text area of the display once. Next,
Schedule-memo data appears on the display.
You can interrupt scrolling of the initial text
and immediately display Schedule-memo data
at any time by pressing A, B, or C.
Notes
A Schedule-memo Alarm sounds whenever a time you set is reached. It
continues for about 20 seconds or until you interrupt it by pressing any
button.
The Schedule-memo text scrolls across the text area of the display only if
the watch is in the Timekeeping Mode when the Schedule-memo time is
reached. The text continues to scroll for about 25 seconds, or until you stop
it by pressing any button after you press a button to interrupt the alarm.
Schedule-memo Mode data items are automatically sorted into chronological
order.
Entering the Schedule-memo Mode causes data for the next scheduled
appointment to appear on the display.
To input new Schedule-memo data
1. In the Schedule-memo Mode, press B or C
until the new data display appears.
If there is no Schedule-memo data stored in
memory yet, the new data display appears as
soon as you enter the Schedule-memo Mode.
If the message
FULL appears in the text area
of the display, it means that memory is full. To
store more data, you will first have to delete
some of the data stored in memory.
TIMETEL
SCHVIT ALM
STW
B
M
A
C
[New Data Display]
Number area
Month – Day