Casio 1809 Watch User Manual


 
G’MIX
(
F
)
-1
GENERAL GUIDE
The configuration of this watch may differ somewhat from that shown in the illustration.
Press
CC
CC
C to change from mode to mode.
In any mode, press
DD
DD
D to illuminate the display for about two seconds.
The animated figures perform a variety of different actions, depending on the mode the watch is in.
Timekeeping Mode Alarm Mode
Stopwatch Mode
TIMEKEEPING MODE
Use
EE
EE
E to switch the display between month/date
and date/day of the week.
Press
BB
BB
B to play a melody for about 10 seconds.
Pressing any key while a melody is play stops the
melody. The melody that plays depends on when
you press
BB
BB
B.
Date
PM
indicator
Hour
Minutes
Seconds
Day of the week
To set the time and date
1.Hold down
AA
AA
A while in the Timekeeping Mode. The seconds digits flash on the
display because they are
selected
.
2.Press
CC
CC
C to change the selection in the following sequence.
Alarm on
indicator
Hourly time
signal on
indicator
Cur-
rent
time
Mode indicator
Hour
Minutes
To set the alarm time
1.Hold down
AA
AA
A while in the Alarm Mode. The hour digits flash on the display be-
cause they are
selected
.
At this time the Daily Alarm is switched on automatically.
2.Press
CC
CC
C to change the selection in the following sequence.
3.Press
EE
EE
E to increase the selected digits and
BB
BB
B to decrease them. Holding down
either button changes the selection at high speed.
The format (12-hour and 24-hour) of the alarm time matches the format you select
for normal timekeeping.
When setting the alarm time using the 12-hour format, take care to set the time
correctly as morning or afternoon.
4.After you set the alarm time, press
AA
AA
A to return to the Alarm Mode.
If you do not operate any button for a few minutes while a selection is flashing, the
flashing stops and the watch goes back to the Alarm Mode automatically.
If you do not operate any button for a few minutes in the Alarm Mode, the watch
goes back to the Timekeeping Mode automatically.
To switch the Daily Alarm and Hourly Time Signal on and off
Press
EE
EE
E while in the Alarm Mode to change the status of the Daily Alarm and Hourly
Time Signal in the following sequence.
ALM: Daily Alarm
SIG : Hourly Time Signal
To test the Alarm
Pressing
BB
BB
B sounds the currently selected alarm sound.
It takes about 10 seconds for the alarm sound to finish. You can stop it manually by
pressing any key.
Note that if 0 is set as the alarm sound, pressing
BB
BB
B randomly selects one of the
melodies. The sound that is randomly selected when the next alarm time is reached
will probably be different from the one that sounds when you press
BB
BB
B.
STOPWATCH MODE
The Stopwatch Mode lets you measure elapsed time,
split times, and two finishes. The range of the stop-
watch is 23 hours, 59 minutes, 59.99 seconds.
Animated figures appear on the display while the
stopwatch is measuring an elapsed time.
If you do not perform any key operation while in
the Stopwatch Mode, the watch automatically re-
turns to the Timekeeping Mode (except when an
elapsed time measurement is in progress.
To measure elapsed time
1.Press
EE
EE
E to start the stopwatch.
2.Press
EE
EE
E to stop the stopwatch.
You can resume the measurement operation by
pressing
EE
EE
E again.
3.Press
BB
BB
B to clear the stopwatch to all zeros
(0H00’00”00).
To record split times
1.Press
EE
EE
E to start the stopwatch.
2.Press
BB
BB
B to display the timing up to that point. Stopwatch timing continues internal-
ly.
3.Press
BB
BB
B to clear the split time and to continue time measurement on the display.
You can repeat steps 2 and 3 as many times as you want.
4.Press
EE
EE
E to stop the time measurement.
5.Press
BB
BB
B to clear the stopwatch to all zeros.
To time first and second place finishes
1.Press
EE
EE
E to start the stopwatch.
2.Press
BB
BB
B when the first finisher crosses the line, and record the time.
3.Press
EE
EE
E when the seconds finisher crosses the line.
4.Press
BB
BB
B to display the finishing time of the second finisher.
5.Press
BB
BB
B to clear the stopwatch to all zeros.
Hours
Mode indicator
Minutes
Seconds
1/100 seocnd
1623 1667 1668 1678 1807 1808 1809 1852
1853 1854 1855 1891 1932 1952 1955 2142
3.While the seconds digits are selected (flashing), press
EE
EE
E to reset the seconds to
“00”. If you press
EE
EE
E while the seconds count is in the range of 30 to 59, it is reset
to “00” and 1 is added to the minutes. If the seconds count is in the range of 00 to
29, the minutes count is unchanged.
4.While any other digits (besides seconds), are selected (flashing), press
EE
EE
E to in-
crease the number or
BB
BB
B to decrease it. Holding down either button changes the
current selection at high speed.
While the day of the week is selected, pressing
EE
EE
E advances to the next day, while
pressing
BB
BB
B returns to the previous day.
While the 12/24-hour setting is selected, press
EE
EE
E to switch between the two for-
mats.
5.After you set the time and date, press
AA
AA
A to return to the Timekeeping Mode.
The date can be set within the range of January 1, 1995 to December 31, 2039.
If you do not operate any button for a few minutes while a selection is flashing, the
flashing stops and the watch goes back to the Timekeeping Mode automatically.
ABOUT THE BACKLIGHT
Pressing
DD
DD
D at any time illuminates the display for about two seconds and causes
an animated figure to appear. The type of animation that appears depends upon
when you press
DD
DD
D.
The backlight of this watch employs an electro-luminescent (EL) light, which loses
its illuminating power after very long term use.
The watch will emit an audible sound whenever the display is illuminated. This is
caused by a transistor that vibrates when the EL panel lights up. It does not indicate
malfunction of the watch.
ALARM MODE
This watch include three built-in melodies, which you
can use in any of the following five settings to sound
when an alarm time is reached.
See the MELODY LIST at the back of this manual for the names of melodies.
When the Daily Alarm is switched on, the alarm sounds for about 20 seconds at the
preset time each day. Press any button to stop the alarm after it starts to sound.
When the Hourly Time Signal is switched on, the watch beeps every hour on the
hour.
Seconds Hour Minutes Year
12/24-Hour
Format
Date Month
Day of
the week
Hour Minutes Alarm Sound
Both OFF
Daily Alarm Hourly Time
Both ON
only Signal only
Setting
Alarm Sound
0. Random play of melodies 1, 2, and 3
1. Melody 1
2. Melody 2
3. Melody 3
4. Beeper