Filter
Top Products
2255 Brunton Court, Riverton, WY USA 82501
PH: 307.857.4700
www.brunton.com
Brunton warrants this product to be free of defects in workmanship and materials for the
lifetime of the original owner, and is nontransferable. If you have any problems with your
Brunton stove, the stove should be returned to the dealer or sent to Brunton, 2255
Brunton Court, Riverton, WY 82501 U.S.A. Please contact Brunton at the number below
to obtain RA#. Clean food and soot from stove before shipping. Shipping cost to Brunton
is the responsibility of the purchaser. Return postage will be paid by Brunton. Please
return this warranty card to Brunton as a proof of purchase. This warranty does not cover
damage caused by accident, misuse, abuse, or tampering. A nominal charge will be
assessed to repair such damage.
Brunton assumes no responsibility for any inconvenience, loss, or injury, direct or
consequential damage arising from possession or use of the goods. This warranty gives
you specific legal rights which may vary from state to state. Check with your local state
about your rights.
LIMITS OF LIABILITY
www.brunton.com
B A N TA M
TM
Please read, understand and follow all instructions and warnings before using this
product. The proper fuel bottle for this product is included.
BRUNTON
ATTN: WARRANTY DEPT.
2255 BRUNTON COURT
RIVERTON, WYOMING 82501
307.857.4700
BRUNTON WARRANTY REGISTRATION
NAME_______________________________________________________
ADDRESS___________________________________________________
CITY_________________________ST/PROV_______ZIP__________
PHONE _______________________EMAIL_______________________
MODEL#__________________DATE PURCHASED____________
PURCHASED FROM_______________________________________
CITY_________________________ST/PROV_______ZIP__________
PRICE PAID $___________________
1006
VISIT OUR WEBSITE AT www.brunton.com
Warranty card must be filled out completely and returned within 30 days with proof of purchase for warranty to be valid.
- Before using the Brunton Bantam stove, please read and follow all the steps
below carefully.
1. Pour the fuel up to the fill line on the bottle. Do not overfill.
2. Insert pump and turn clockwise to tighten.
To avoid the possibility of serious injury, use only a Brunton pump and bottle.
Use only White Gasoline, other fuel could clog the nozzle and may cause a fire hazard.
Keep away from children.
Filling the fuel bottle
OPERATING INSTRUCTIONS
Using the stove on uneven surface is very dangerous and may cause a fire hazard
and serious injury.
When the fuel bottle has been connected to the pump be sure that the valve knob is set
to the OFF position.
When the stove is in use, keep fuel bottle as far away as possible.
Using the stove Preheating the stove
- Before using the stove with white gas, it is necessary to pre-heat the fuel. This is called
priming the stove.
1. Turn the valve knob counter clockwise to the (ON) position and wait 1-2 seconds until the
jet emits a small amount of fuel onto the priming pad then close the valve by rotating the knob
counter clockwise to the (OFF) Position. If fuel does not flow, the fuel bottle is low on
gas and the bottle may need preasurizing or more fuel.
2. After connecting the flexible hose to
the pump, ensure that the fuel bottle is
placed on a flat surface.
1. Unfold the stove legs and place the stove on a flat surface.
2. After the fire extinguishes, the stove will remain hot, wait until the stove cools down.
3. Separate the stove from pump.
4. Fuel bottle and pump can be transported as a connected assembl
y
y. When separating the
pump from fuel bottle, turn the pump slowly so that the pressure retained inside the fuel
bottle can release gradually
.
1. To extinguish the stove, turn the valve knob to the OFF position and flip the bottle over.
NOTE: The stove will continue to burn for a short time until all of the fuel in the generator tube
and fuel hose is consumed.
Turn slowly counter-
clockwise after preheating
Flip
Small flame remains for 2-3
minutes consuming all the fuel in
the hose.
Dried or torn parts need to be replaced. Check the color and size and any printed
markings and contact your nearest Brunton stock list or retailer for replacements.
(Oil seals, Oil, Nozzle, Tool kit)
Poor performance & nozzle clogging
- Colgging inside the nozzle or generator tube may disturb the fuel and create poor stove
performance.
- Remove clogging inside the nozzle hole with a nozzle pin.
- If clogging persists inside of the nozzle or generator tube, a more thorough cleaning
is required.
A) How to clean with nozzle pin
1. Turn off the stove valve and wait until the stove has completely
cooled down.
2. Remove the Jet by disassembling and removing the generator tube
assembly from the stove with the tool kit.
3. Clean the jet with the nozzle pin
4. Re-Assemble the stove and check for any fuel leaks.
- If cleaning the Jet does not improve the stove efficiency, clean the generator tube as well.
B) How to clean the generator tube
1. Begin by removing the generator tube assembly from the stove with
the tool kit.
2. Pull the wire out brush clean of any debris and replace
3 . Re-Assemble the stove and check for any fuel leaks
leg A
o-ring
leg B
leg pin
fill line
20-30 times
head
oil plate
leg B
guide spring
guide
nozzle
connect nut
nozzle
connect bolt
o-rings
pump knob
hose cap
hose
nozzle
connect
nozzle
body nut
hose
washer
heating pipe
bolt
nozzle
filter
heating pipe
nozzle body
valve
connect
valve connect bolt
pipe bushing
pipe bolt
venturi
wave washer
ring
pump knob
pipe bolt
pipe bushing
guide spring
guide
packing washer
guide washer
packing holder
packing rubber
connect bushing
head assembly
housing cap
nylon hose
filter
setting bushing
spindle
setting bolt
knob
o-rings
pipe
o-rings
o-ring
air spring
air bolt
air bushing
air bushing body
housing
Instructions for 81-100726
3. Before pumping pressure into the fuel
bottle, ensure that the control valve for the
stove unit is set to the OFF position. Pump
the handle on the pump set to pressurize
the fuel bottle (20 strokes).
NOTE: Less fuel in the bottle needs more
pumping strokes to pressurize the bottle.
WARNING
WARNING
WARNING
WARNING
Use outdoors only and do not allow children to reach
1-2 seconds
Manual ignition
Preheating Working
Before igniting the stove, ensure that the valve knob is turned to
the clockwise (OFF) position.
Never place your head or body above the stove when lighting it.
2.
After fuel has been primed to the stove, ignite the fuel through the ignition port with a
lighter or a match to preheat the generator pipe.
3. After pre-heating (1-2minutes) slowly open the valve to allow fuel to flow through the
generator unit. The flame may appear yellow for the first minute of operation but should
settle to a crisp blue flame that is the normal cooking flame. If an excessively high yellow
flame is evident, turn off the stove and repeat the preheating process.
4. Never allow fuel to overflow from the stove base, as leaking fuel will ignite and may
cause a fire hazard and serious injury.
5. If the flame decreases in intensity, further pressurization of the fuel bottle is required.
Extinguishing the stove
Hissing
Separation
Inner pressure exclusion
Pump parts
Stove parts
PARTS REPLACEMENT AND MAINTENANCE
Checking & replacing seals and 0-rings
After disassembling and assembling, be sure to check for leakage with soapy water.
WARRANTY
WARNING
Only use in well ventilated areas.
Do not leave unattended while in use.
Keep well away from children.
Do not operate near flammable materials.